Publicidad
automotive and chemical industry. With the use of proper tools, the
angle grinder can be used not only for cutting or grinding, but also
for rust and paint coats removal.
The areas of its application include repair and construction works,
not only related to metals. The angle grinder can also be used for
cutting and grinding of construction materials, such as brick, paving
stones, ceramic tiles, etc.
The power tool is designed for dry operation only and it must
not be used for polishing. The power tool should be used
according to its purpose.
Use inconsistent with its purpose
• Do not work materials that contain asbestos. Asbestos is
carcinogenic.
• Do not work materials, whose dust is inflammable or
explosive. During operation, the power tool produces sparks, which
may ignite emitted vapours.
• Do not use cut-off wheels for grinding. The cut-off wheels are
used to cut with its face, while grinding with lateral surface of such
a cut-off wheel threatens with its damages and puts the operate in
danger of injuries.
DESCRIPTION OF GRAPHIC PAGES
The below list refers to device components shown in the graphic
pages of this instruction manual.
Spindle lock button
1.
Switch
2.
Additional handle
3.
Grinding wheel cover
4.
Quick release outer flange
5.
Internal flange
6.
Lever (grinding disc guard)
10.
* There can be differences between the drawing and actual product.
DESCRIPTION OF USED GRAPHIC SIGNS
NOTE
WARNING
FITTING/SETTING
INFORMATION
EQUIPMENT AND ACCESSORIES
Grinding wheel guard
1.
2.
Additional handle
Cut-off wheel
3.
PREPARATION FOR WORK
ATTACHING THE ADDITIONAL HANDLE
The additional handle (3) is installed in one of the holes in the
grinder head. It is recommended to use the grinder with the
additional handle. When holding the grinder with both hands (also
using the additional handle), there is less risk of touching the grinder
wheel or brush with your hand, as well as of injuries during recoil.
INSTALLING AND ADJUSTING THE GRINDING WHEEL GUARD
The wheel guard protects the operator against flying broken
pieces and accidental contact with a working tool or sparks. The
guard should always be fitted. Special attention should be paid
so that its covering part faces the operator.
IThe design of the wheel guard mounting allows for toolless setting
of the guard in an optimum position.
• Loosen and pull back the lever (10) on the wheel guard (4).
- 1 pce
- 1 pce
- 4 pce
• Rotate the wheel guard (4) in a selected position.
• Lock by lowering the lever (10).
The removal and adjustment of the wheel guard are performed in a
reverse order to its installation.
REPLACEMENT OF WORKING TOOLS
When working tools are replaced, wear working gloves at all times.
The spindle lock button (1) is only designed to lock the grinder
spindle, when a working tool is installed or removed. Do not use
it as a braking button, when the wheel rotates. Otherwise, the
grinder may become damaged or the user may be injured.
INSTALLING THE WHEELS
Disc installation does not require tools thanks to use of the quick
release outer flange. Rim of the quick release outer flange has special
knurled texture for easier grip in hand.
Before disc installation make sure the inner flange (6) has a
rubber O-ring installed and that the ring is not damaged (fig. L).
• Press the spindle lock button (1) (fig. A).
• Loosen and unscrew the quick release outer flange (5).
• Put the disc on, so it is pressed against surface of the outer flange
(6) and centred when seated on its neck (fig. B).
• Screw on the quick release outer flange (5) (right hand thread).
This step is illustrated on the picture (fig. M).
• Press the spindle lock button (1), screw the quick release outer
flange (5) on and tighten with strong clockwise rotation of the
disc (fig. N).
Make sure to keep the surfaces of inner and outer quick release
flange clean. Always attach the outer quick release flange with holes
and text surface outwards.
To remove the disc, press the spindle lock (1), loosen and undo the
outer quick release flange (5).
INSTALLING THE WORKING TOOLS WITH THREADED HOLES
• Press the spindle lock button (1).
• Remove a previously installed working tool, if it is installed.
• Both flanges should be removed before installation – the inner
flange (6) and outer flange (5).
• Put the threaded part of a working tool onto the spindle and
slightly tighten.
Working tools with threaded holes are removed in the reverse order.
INSTALLING THE ANGLE GRINDER ON A TRIPOD FOR ANGLE
GRINDERS
The angle grinder can be used on a dedicated tripod for angle
grinders, provided that it is correctly installed according to
instructions of the manufacturer of a tripod.
OPERATION / ADJUSTMENTS
Before the grinder is used, check condition of the grinding
wheel. Do not use chipped, broken or otherwise damaged
grinding wheels. Worn grinding wheel or brush should be
immediately replaced with new one before use. Once your work
is completed, you should switch off the grinder and wait until
it comes to a complete stop. Only then the grinder can be put
aside. Do not brake a rotating grinding wheel by pressing it
against a workpiece.
• Do not overload the grinder. The weight of the power tool
exerts sufficient pressure to efficiently work with the tool.
Overloading and excessive pressure may lead to dangerous
cracking of the working tool.
• If the grinder is dropped during operation, it should be
checked and a working tool might need to be replaced, when
it is damaged or deformed.
• Never strike the workpiece with a working tool.
• Do not use the grinding wheel for hammering or stripping
of the workpiece, especially when corners, sharp edges are
16
Publicidad
