Cardin Elettronica S449-QZ1 Manual De Instrucciones página 2

CARDIN ELETTRONICA spa
Via Raffaello, 36- 31020 San Vendemiano (TV) Italy
Tel:
Fax:
email (Italy):
email (Europe):
Http:
DIGITAL RADIO CONTROLS WITH ROLLING CODES S449
Description
The S449 Radio control system in "FM" consists of one or more transmitters and one or more receivers which can
be combined to meet the specific needs of the system. The S449 system uses a highly reliable encoding system
guaranteed by the use of dynamic codes. The code is changed for each encoding transmission through the use
of an encoding algorithm which only the receiver is able to recognise and therefore decide whether or not the
code transmitted corresponds to the original code. As the system use dynamic codes each code is managed
individually by the receiver
Important: The transmitted code changes for each command (rolling code). If disturbance interrupts the transmission,
the receiver will wait for a different code, the relay can then only be activated by first releasing and then pressing
the transmitter channel button again.
Use
The S449 radio control allows the remote activation of electrical and electronic appliances with its best use in the following
areas: automatic opening systems, alarm systems and multiple access systems (apartment blocks etc.) and in all systems
which require remote control activation (without wires) using secret codes.
The receiver has been designed for multiple access with UP to 1000 each of which may be memorised or cancelled indi-
vidually. Each code is stored in a memory location chosen on the display and the location can activate UP to 4 functions.
1 transmitter = 4 functions max. = 1 location; 1000 users = 4000 functions max.
Transmitter versions
TRQ449100 Miniaturised transmitters
TRQ449200 Miniaturised transmitters
TRQ449300
Miniaturised transmitters
TRQ449400 Miniaturised transmitters
TRQ44940M Wall mounted transmitters
Receiver versions
RCQ449D00 Outdoor receiver with display (1000)
Memory module
This is extractable, furnished with a non volatile EEPROM 24C64 type memory and contains the transmitter codes. The
programmed codes are maintained in this module even in the absence of power without a time limit.
Antenna
To obtain the best results from the radio control device the installation of the antenna is fundamental as once connected to
the receiver it represents the reception point for the transmitter. A tuned antenna using a coaxial cable RG58 (impedance
50Ω) with a maximum length of 15m. must be installed. The antenna should be positioned out of doors in the highest
possible point, visible and away from metal structures. The receiver should be positioned away from computer systems,
alarm systems and other possible sources of disturbance.
Transmitters
The transmitter is pre-coded and is fitted with an integrated circuit which is programmed in the factory with a unique
identification number. All the code parameters are contained in this integrated circuit (external memory modules are not
required) thus making code management more reliable and the system more secure.
The transmitter has an automatic shut down mechanism which cuts in after 25 seconds of continuous use (this limits
battery consumption). This time can vary from transmitter to transmitter.
Receivers
Warning! The receivers must only be powered by a safety power pack. The use of non safety power packs
could provoke damage to the system.
Outdoor receiver with display (fig.4)
- The outdoor receiver card (printed circuit CS1127a) is fitted with an 14-way terminal board and has the following electrical
connections:
12V ac/dc between binding posts 1-2.
24V ac/dc between binding posts 1-3.
The outdoor receiver is fitted using "fast-fitting" brackets. The bracket should be fixed to the wall using two rawlplugs
(check that it is in square). After connecting the wiring the case should be slid onto the bracket therefore fixing
it to the wall. If any repair work is necessary the case can be easily extracted by pushing upwards the action of
which will separate it from the bracket.
Interchangeable channel modules
In the receivers the channel functions are printed on the circuit board. Only type MCC4491R0 relays can be used.
Attention! If the receiver is powered by "24V" you may simultaneously activate two of the four available relays plus
one impulsive relay. It follows therefore that you must pay attention to the type of function each relay has. If the
receiver is powered by "12V" there is no limitation.
Receiver functions
The following functions are managed by the PGM449 for more details consult the manual supplied with the product.
Blocking buttons: The receiver programming buttons can be disabled to prevent unauthorised use.
PIN code security: This function uses a PIN code to prevent unauthorised use of the receiver.
TRS substitution: This function allows you to replace a transmitter without opening the container
Attention! Before memorising the transmitters for the first time remember to cancel the entire memory content.
A - Setting UP relays (fig. 5)
• The display type receiver S449 uses an "Impulsive" type relay that can be programmed as an "On-Off" or "Zeitschalter"
relay by the receiver. When setting UP relays the UP/DOWN/MEMO and DEL buttons have special functions.
• When the receiver switches on the firmware version will be shown. This is represented by an "r" followed by two digits
which will disappear after one second. If the palm has enabled the PIN code security function (in the receiver memory)
the flashing indication "PIN" will appear and disappear after 10 seconds. The location number "001" (fig. 5a) will now
automatically appear indicating that the receiver is ready to accept a command. The indications on the display are
maintained for 4 seconds after the last command was received (either via radio or using the buttons on the receiver)
after which the stand-by mode will appear; only the right hand decimal point will be lit (fig.5b).
To program the relays proceed as follows:
1) Simultaneously press the "UP" and "DOWN" buttons (fig.5c) and the central line on the display will light UP. If you
keep the buttons pressed DOWN for 10 seconds the symbol (fig.5d) will appear, indicating that you have entered the
relay programming mode.
2) Using the "UP" button (fig.5e) choose the function you wish to modify. Each time you press the button the display will
show the next function in the sequence CH-A,B,C,D (fig.5e,f,g,h).
3) Using the "DOWN" button (fig.5i) choose the relay mode to associate with each channel. Each time you press the
button the display will show the setting in the following sequence "Impulsive", "Zeitschalter","ON/OFF" (fig.5j,k,l)
4) To set the Zeitschalter in the "Zeitschalter relay method" (fig.5K) press the MEMO/DEL (fig.5m), set the desired time
using the "UP" and "DOWN" buttons (e.g. 120 seconds fig.5N) then press the MEMO/DEL button again (fig.5Q). The
chosen time will be set for the desired relay.
5) To confirm the new channel settings, press the "UP" button until the symbol (fig.5p) appears on the display and then
wait for 20 seconds after which period the receiver will store the new settings.
6) To exit the relay programming mode without saving the changes wait for twenty seconds with anything on the display
other than the indication in (fig.5p). The receiver will ignore any changes which have been made.
+39/0438.404011-401818
+39/0438.401831
Sales.office.it@cardin.it
Sales.office@cardin.it
www.cardin.it
1 button
2 buttons
3 buttons
4 buttons
4 buttons
4 channels
SERIAL NUMBER
ZVL415.01
The S449 series conforms to the essential requirements of the directive 99/
05/CE and the technical reference standards have been applied.
Frequency validity: 433.92 MHz for all
B - Memorising a channel (fig. 6)
• It is possible to add new transmitters or program new functions into an already memorised transmitter at any
time with the following exceptions:
- If the transmitter you wish to memorise is already present in a different memory location or the function is
already present, the receiver will automatically exit the programming mode and indicate the location in which
the transmitter code is memorised.
- If the receiver doesn't appear to respond to the transmitter button, wait for a few seconds (if you have a high number
of codes memorised the receiver). To avoid accidentally memorising transmitters the receiver will ask you to confirm
the transmitted code by pressing the channel a second time.
- All operations are carried out manually. If you release the "MEMO/DEL" before the procedure has terminated nothing
will be memorised.
- The dots on the display indicate the location status: no lit dots indicates an empty location; one lit dot indicates an
occupied location (1 to 3 channels); two lit dots indicates an entirely occupied location (4 channels)
1) Make sure the jumper "J1" (fig 4-6a) is inserted.
2) Choose the desired location using the "UP" and "DOWN" buttons (fig 6a) which increase and decrease the displayed
number (keep the button pressed DOWN to scroll faster).
3) Press the "MEMO/DEL" button and make sure that (fig 6c) appears.
4) Press (for about 1 second) the button on the transmitter that you wish to memorise (fig 6d) until either the symbol (fig
6e) or an already memorised location appears.
5) Press the channel button a second time to confirm it and a letter indicating the inserted function will appear on the
display e.g. (a,b,c or d, as shown in fig 6f).
6) The procedure is now finished. Release the button and the memory location will be shown with the status points updated
e.g. (fig 6g-h).
7) To memorise another channel button repeat from point 3; for a new transmitter repeat from point 2.
C - Cancelling a channel/user or entire user memory (fig. 7)
• You do not need to have the transmitter to be able to cancel. This allows you to cancel a transmitter which has
been lost without having to cancel all codes and consequently having to re-insert all the codes (obviously you must
already know the memory location for this to work.
Caution! Keeping the MEMO/DEL button pressed for more than 20 seconds will wipe the entire memory (the codes
cannot be recovered). The indication "CLA" appears on the display (fig 7k) when the entire user memory has been
cleared.
1) Make sure the jumper "J1" (fig 4-7a) is not inserted.
2) Choose the desired location using the "UP" and "DOWN" buttons (fig 7b) which increase and decrease the displayed
number (keep the button pressed DOWN to scroll faster).
3) Press the "MEMO/DEL" button and make sure that the indication in (fig 7c) appears.
4) The letters indicating the function will appear on the display in sequence (fig 7d-f) separated by the "Nil" indication (fig
7e-g). After the four function letters have appeared the symbol "ALL" (fig 7h) will appear on the display (indicating that
the entire location has been cancelled) after which the sequence will start again. Only the memorised functions will be
shown so if the location is empty the "Nil" indication (fig 7i) will be shown followed by the symbol "ALL" (fig 7h). Keep
the button pressed to scroll through the indications on the display and release the button when you reach the desired
location. Releasing the button with the "Nil" symbol (fig 7i) on the display will abort the cancellation procedure leaving
the location unaltered.
5) If a cancellation operation has been selected the indication (fig 7j) will appear to confirm that the command has been
carried out after which the memory location will once again be shown.
6) Repeat points 1 to 4 for all ulterior cancellation procedures.
ERROR CONDITIONS
• The receiver is fitted with error diagnostics. The error situations are indicated on the display by the symbol "Er" flashing
followed by an error identification number. The error numbers are as follows:
WRONG MEMORY PARAMETERS
• The parameters in the memory module are wrong and the receiver will attempt to manage any eventual data it can
read in order to allow the receiver to function. This indication can also be caused by a new memory module (not yet
set up to operate) or by a defective or corrupt memory module. If the error indication persists do not use the receiver
and contact the after sales service.
MEMORY MODULE MISSING OR DAMAGED
• The receiver is unable to read the code memory and to preserve the data contained in the module it will block the
operation and signal this error code. This error will also appear if the receiver is switched on without a memory module
inserted or if you remove the module while the receiver is functioning (THIS MUST NEVER BE DONE!).
CORRUPT PIN CODE
• The PIN code security data is corrupt. The receiver will be blocked because this could be the result of an attempt to
breach the installation security. Consult the PGM449 instructions for how to manage this error.
TECHNICAL SPECIFICATIONS
Receiver
- reception frequency......................................................................................................................................... 433,92 MHz
- local oscillation frequency .............................................................................................................................. 433,22 MHz
- local oscillation tolerance ...................................................................................................... ±30 PPM from -20 to +75°C
- local oscillation emission......................................................................................................................................<-57dBm
- sensitivity (finely tuned signal) ................................................................................................................. -110 dBm 0,7 µV
- selectivity ............................................................................................................................................................... ±30 kHz
- modulation .................................................................................................................................................................... FSK
- modulation with ΔF................................................................................................................................................≤ 20 kHz
- antenna impedance in input ......................................................................................................................................... 50Ω
- receiver power supply .................................................................................................................................. 12/24V ac/dc
- maximum power consumption (depending on the number of relays).............................................................. 22/145 mA
- maximum commutable power at the relay with ac/dc resistive load: ..............................................................60VA/24W
maximum voltage applied at the relay contacts .................................................................................................30Vac/dc
- relay activation delay time ..................................................................................................................................0,1 ÷ 1,3 s
- operating temperature range.......................................................................................................................... -20°...+75°C
Transmitters
- carrier frequency.............................................................................................................................................. 433.92 MHz
- carrier frequency tolerance.................................................................................................................................... ±30 kHz
- apparent radiated power ...........................................................................................................-10...-7dBm (100-200µW)
- apparent power harmonic products.......................................................................................................<-54 dBm (<4nW)
- modulation ..............................................................................................................................................................FM/FSK
- modulated with ΔF.................................................................................................................................................≤ 20 kHz
- power supply (lithium battery) ..........................................................................................................................2 x CR2032
- power consumption.................................................................................................................................................. 35 mA
- operating temperature range........................................................................................................................... -10...+55°C
- relative humidity........................................................................................................................................................ < 95%
- type of encoding................................................................................................................ rolling code (2
- number of channels ...........................................................................................................................................................4
- automatic shut down...................................................................................................................after at least 25 seconds
SERIES MODEL
S449 D00 02-07-2001
countries
DATE
66 combinations )