Publicidad
Idiomas disponibles
Idiomas disponibles
90508554 Circ Saws REV
SAFETY WARNINGS AND INSTRUCTIONS: CHARGING
1. This manual contains important safety and operating instructions.
2. Before using battery charger, read all instructions and cautionary warnings on battery
charger and product using battery.
CAUTION: To reduce the risk of injury, use charger only with this product. Batteries in
other products may burst causing personal injury or damage.
3. Do not expose charger to rain or snow.
4. Use of an attachment not recommended may result in a risk of fire, electric shock, or
injury to persons.
5. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when
disconnecting charger.
6. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise
subjected to damage or stress.
7. An extension cord should not be used unless absolutely necessary. Use of improper
extension cord could result in a risk of fire, electric shock or electrocution.
a. Two-wire cords can be used with
2-wire or 3-wire extension cords. Only round jacketed extension cords should be
used, and we recommend that they be listed by Underwriters Laboratories (U.L.). If
the extension is to be used outside, the cord must be suitable for outdoor use. Any
cord marked for outdoor use can also be used for indoor work. The letters "W" or
"WA" on the cord jacket indicate that the cord is suitable for outdoor use.
b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for
safety, and to prevent loss of power and overheating. The smaller the gauge number
of the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity
than 18 gauge. When using more than one extension to make up the total length, be
sure each extension contains at least the minimum wire size for the total length.
8. Use only the specified charger when charging your tool. The use of any other charger
could damage the tool or create a hazardous condition.
9. Use only one charger when charging.
10. Do not attempt to open the charger. There are no customer serviceable parts inside.
Return to any authorized Black & Decker service center.
11. DO NOT incinerate the tool or batteries even if they are severely damaged or
completely worn out. The batteries can explode in a fire.
12. A small leakage of liquid from the battery cells may occur under extreme usage,
charging or temperature conditions. This does not indicate a failure. However, if the
outer seal is broken and this leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10
minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a
25-35% solution of potassium hydroxide.
CHARGING THE BATTERY - SINGLE PORT CHARGER
THE BATTERIES IN YOUR POWER PACK ARE NOT FULLY CHARGED AT THE
FACTORY. BEFORE ATTEMPTING TO CHARGE THEM, THOROUGHLY READ ALL OF
THE SAFETY INSTRUCTIONS.
The charger is designed to use standard household 120 volt 60 Hz power. NOTE: Do not
charge by means of an engine generator or DC power source. Use only 120V AC.
1. Plug the charger into any standard 120 Volt 60 Hz electrical outlet.
2. Slide the charger onto the battery pack as shown in Figure A and let it charge initially
for 9 hours. After the initial charge, under normal usage, your power pack should be
fully charged in 3 to 9 hours.
3. Remove pack from the charger and place in tool. NOTE: To remove the battery from
the saw, press down on the release button on the back of the battery (Figure B) and
pull out.
CHARGING THE BATTERY - DUAL PORT CHARGER
1. Plug the charger into an appropriate outlet.
2. Insert 1 or 2 batteries into the charger (Figure AA). NOTE: Charge time is the same
for multiple batteries.
8/22/06
1:22 PM
Page 7
7
Publicidad
