Lemeks Palmako EL16-4228 Instrucciones De Montaje, Instalación Y Mantenimiento página 43

EN
Read these instructions carefully prior to assembly and check the number and condition
of the parts.
Assembly
The product must be installed in accordance with the drawings included in the
manual. At least two people are required to ensure safety of assembly. spirit level, saw,
protective gloves, safety glasses, cordless drill with drill bits and screwdrivers, tape measure, pencil,
stair ladder, wrench set, file are required for assembly. Before screwing, please drill hole
in order to avoid cracks in the wood.
Installation
The product is intended to be used with „Toby 2,1 m2" (EL16-1819). The product must be installed on a smooth
surface covered with an appropriate material: sand, bark or well-maintained grass. Installation must take place in accordance
with the figure labelled "Safety area". The distance between the product and other objects (including those situated above the
ground, such as tree branches) should be at least 2 metres. The product legs must be fixed to the concreted anchors
(as indicated in the drawing). The legs must not be set in sand or another soft surface material, as this may not guarantee
sufficient stability.
Anchoring
To ensure stability, the product must be anchored in the ground. Dig in the soil at the location of the legs
holes that are 400 mm deep and with the cross-section of 600x600mm. Throw a layer
of gravel to the bottom of the hole to improve rainwater absorption in the soil. Then pour concrete into the hole,
stopping at 50 mm below the ground level. When the concrete becomes dry, place a layer of soil on it up to the ground level.
Use
All projecting screws and sharp edges must be planed smooth immediately after installation to avoid potential injuries. The height of the swing seat (350
mm) as well as the general condition of the set must be checked on a daily basis. Stability, wear on the moving parts and strength of connections should be
checked no less frequently than every 1 to 3 months. The suitability of the base material, corrosion of accessories and rotting of wooden parts should be
checked once a year. Moving parts must be oiled and worn and/or defective parts should be replaced with parts provided by the manufacturer. Bolts and
ropes must be tightened.
NB! The product with slide can only be considered safe when it is used with the appropriate slide (height from ground surface 1200±50 mm, maximum
width 500 mm). When installing the slide leave at least 25 mm (30 mm recommended) clearances on both sides, in order to prevent clothing entrapments
during gliding. Providing the product with a suitable slide is the responsibility of the end-seller of the product. The slide that is used must meet the criteria of
the EN 71 of the European Safety Standard and go with the given swing set.
NB! If the product is used with a slide and a swing beam, the slide must not be installed close to the swings. If the swing reaches the starting section
of the slide, it must be removed.
We advise the removal and storage of all accessories during the winter because the characteristics of the soil (when frozen) are not suitable for safe play. To
avoid that the swing is heating up, do not place it facing the sun. In warm weather, check that the seating surface is not too hot.
Warnings.
•
Not suitable for children under 3 years. Risk of falling.
•
To be used under the direct supervision of an adult. Ropes. Suffocation risk.
•
Only for domestic use. Outdoor.
•
Adult assembly required.
•
This product is designed to be used by children from the ages of 3 to 14 (max 50kg/user).
•
The product is designed for simultaneous use by up to 2 persons.
Caution.
•
Items of clothing causing increased danger such as hoods, buttons, etc., may become caught during use of the product and may therefore
present a risk of suffocation to the wearer.
•
Wooden details can contain slight torn grain or sharp ends and edges.
•
Every time before using the playground you should make that the anchoring remains reliable.
NB! The structure MUST NOT be altered without the consent of the manufacturer, otherwise risk of serious injury. These instructions should be kept in
order to avoid later disputes.
For your information:
Wood, as a natural material, is sensitive to changes in the environment. Fluctuations in temperature and weather conditions may cause the wood to split and
harden – particularly in the case of machine-cut wood products. However, this generally does not affect the strength of the wood. This swing design is
foreseen for one-time installation only.
To protect the wooden details of the product, you must immediately process them with a wood preservative.
Ø2 Ø3 Ø4