HERKULES H-FS 800 Manual De Instrucciones página 15

A load factor of S2 10 min (intermittent periodic
duty) means that you may operate the motor
continuously at its nominal power level (800 W)
for no longer than the time stipulated on the spe-
cifi cations label (10 minutes ON period). If you fail
to observe this time limit the motor will overheat.
During the OFF period the motor will cool again to
its starting temperature.
Idle speed
L sound pressure level ............................. 92 dB
pA
L sound power level .............................. 105 dB
WA
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
4. Important information
Please read the operating instructions carefully
and observe the information provided. It is im-
portant to consult these instructions in order to
acquaint yourself with the equipment, its proper
use and safety regulations.
Danger!
For safety reasons, the tile cutting machine is not
to be used by children, young people under 16
years of age, or any other persons who are not
acquainted with these operating instructions.
Anl_H_FS_800_SPK7.indb 15 Anl_H_FS_800_SPK7.indb 15
GB
5. Intended use
The tile cutting machine is designed for the
standard cutting of small and medium-size tiles
(glazed tiles, ceramic tiles or similar) which can
be accommodated by the size of the machine. It
should never be used for cutting wood or metal.
The machine should be used exclusively for
its intended purpose. Any other use is deemed
to be a case of misuse. The user/operator and
not the manufacturer will be held liable for da-
mage and/or injuries of any kind that result from
such misuse. The machine is to be operated
only with suitable cutting-off wheels. Saw blades
should never be used. Compliance with the sa-
fety instructions, the assembly instructions, and
advice and instructions on operation contained
in the operating instructions also falls under the
terms of intended use. All persons who use and
service the equipment have to be acquainted
with this manual and must be informed about the
machine's potential hazards. In addition, strict
compliance with the accident prevention regulati-
ons in force in your area, as well as all other ge-
neral rules of health and safety at work, is impera-
tive. The manufacturer's liability shall be deemed
void if the machine is modifi ed in any way and the
manufacturer shall therefore accept no liability for
any damages arising as a result of modifi cations.
Even when the equipment is used as prescribed
it is still impossible to eliminate certain residual
risk factors. The following hazards may arise in
connection with the machine's construction and
design:
•
Contact with the diamond cutting wheel whe-
re it is not covered.
•
Contact with the diamond cutting wheel while
it is turning.
•
Defective diamond tips flying off the cutting
wheel.
•
Kick-back of workpieces and parts of workpi-
eces due to improper handling.
•
Damage to hearing if ear-muffs are not used
as necessary.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
- 15 -
01.02.2017 08:37:48 01.02.2017 08:37:48