stayer BVAC2200E Manual De Instrucciones página 12

Some examples of these chemicals are:
Lead from lead-based paints, crystalline silica from bricks
and cement and other masonry products, and arsenic
and chromium from chemically-treated lumber. The risk
from these exposures varies, depending on how often
you do this type of work.
To reduce your exposure to these chemicals: work in
a well ventilated area, and work with approved safety
equipment, such as dust masks that are specially
designed to filter out microscopic particles.
INTENDED USE
This vacuum cleaner is primarily designed to operate
in conjunction with power tools which require dust
extraction, such as sanders, saws, wall chasers,
scouring machines,
nondangerous dusts, dirt, shavings etc.
This machine may also be used to vacuum water and
other non-flammable and non corrosive liquids.
The end user/operator is solely responsible for any
damage or accident should the machine be used for any
use other than its intended purpose.
PREPARATION AND INITIAL OPERATION
Electrical connection.
The operating voltage shown on the rating plate must
correspond to the voltage of the power supply. Make
sure that the vacuum cleaner is switched off when you
plug the power supply.
This machine must ALWAYS be plugged
into a properly grounded outlet. NEVER
operate the m a c hine if it is not grounded.
This will result in a static electrical build-up
which will destroy the machine's electronic
components.
ASSEMBLY
Follow the sequences in Figures 2 and 3.
OPERATION
Modes of operation:
1. Solid vacuum cleaner. (FIG. A)
Place the hose 4 in the socket 5. Place the cap 19 on the
socket 9 and turn it clockwise.
2. Vacuum cleaner. (FIG.B)
Place hose 4 in port 9. Place cap 19 in port 5 and turn
right.
3. Air blower. (FIG. C)
Place hose 4 in port 10. Place cap 19 in port 5 or port 9
and turn right.
On and off. Fig. 1
Connect cable 13 to an outlet in a regulated installation
that has an earth connection. To turn the machine on or
off use switch 7. See Fig. 1.
etc. This machine
ENGLISH
12
Power Regulation. Fig. 17
To regulate the power of the equipment, use knob 8.
Synchronous auxiliary socket. Fig. 18 and 19
The equipment has an outlet to power equipment,
so that the vacuum cleaner starts when the machine
connected to this outlet is running 18. To do this, press
switch 7 to the position with two horizontal lines. For
equipment, Fig. 18, with suction outlet connect the outlet
of the equipment to outlet 5. For equipment without direct
suction outlet, Fig. 19
EMPTYING THE DEPOSIT
Follow the sequence in figure 22.
Please refer to the Aspira Liquido Debe Colocar and your
extracts deposit.
MAINTENANCE
Accessory location. Fig. 5, 6, 7
The mobility wheels are inserted into the base of the
vacuum cleaner, see Fig. 5.
When the vacuum cleaner is not used the equipment
power cable must be wrapped in the storage straps, see
Fig. 6.
The suction fittings are stored in their storage
compartments, see Fig. 7.
Cycle inversion cleaning, Fig. 9
Each hour of use or if you notice that the suction is down
press the button 11 4 or 5 times to recover all the suction.
Filter bag, Fig. 10 and 11.
To replace it, lift the top cover and attach it to its holder.
HEPA filter, Fig. 12, 13 and 14.
To access the filter, loosen the straps 14, remove the
machine body and turn it to access the parts (Fig. 12).
Remove the filter from its holder as per Fig. 13 and clean
it with soap and water. Before reinstalling allow to dry
completely. See Fig. 14.
Cleaning the connection tube, Fig. 15.
To access the tubes, loosen the straps 14, remove the
body from the machine and turn around to access the
parts (Fig. 12). Manually remove the line and clean it with
tap water (Fig.15).
Filling the water tank, Fig. 16.
To access the tank, loosen the straps 14 and remove the
body from the machine.
Cleaning the filter bag, Fig. 22 and 23.
When full, lift the top cover, remove the bag from its
guide by the mouth and empty the dust by opening the
bottom of the bag. Close and install for new use.
Draining the suction water, Fig. 24.
Move the vacuum cleaner to a drain. Loosen the straps
14, remove the machine body and turn the container to
drain the water. Clean the container with clean water.
12