DeWalt DCH263DH Manual Del Usuario página 35

Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Variable speed switch
1
Forward/reverse button
2
Mode selector dial
3
Mode selector release
4
button
Side handle
5
Battery pack
6
Release button
7
Main handle
8
SDS PLUS bit holder
9
Intended Use
Your cordless rotary hammerdrill has been designed for
professional drilling, hammerdrilling and chipping applications
in concrete and masonry, as well as screwdriving applications in
steel, wood and plastics.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
Your cordless rotary hammerdrill is a professional power tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
Active Vibration Control (Fig. A)
For best vibration control, hold the tool as described in Proper
Hand Position.
The active vibration control 16
from the hammer mechanism. Lowering hand and arm
vibration, it allows more comfortable use for longer periods of
time and extends the life of the unit.
The hammer only needs enough pressure to engage the active
vibraton control. Applying too much pressure will not make
the tool drill or chip faster and active vibration control will
not engage.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
e
Sleeve
10
Depth rod
11
Depth rod release button
12
Worklight
13
Belt hook (optional
14
accessory)
Belt hook screw
15
Active vibration control
16
(AVC)
Dust extraction electrical
17
connector
neutralises rebound vibration
WALT battery packs and chargers.
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack 6 with the rails inside the tool's
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button 7
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button . A combination of the three green LED lights will
19
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Side Handle (Fig. A)

WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the side handle properly installed.
Failure to do so may result in the side handle slipping
during tool operation and subsequent loss of control. Hold
tool with both hands to maximize control.
The side handle 5 clamps to the front of the gear case and
may be rotated 360˚ to permit right- or left-hand use. The side
handle must be tightened sufficiently to resist the twisting
action of the tool if the accessory binds or stalls. Be sure to grip
the side handle at the far end to control the tool during a stall.
To loosen side handle, rotate counterclockwise.
To Adjust the Depth Rod (Fig. C)
1. Push in and hold the depth rod release button
side handle.
2. Move the depth rod so the distance between the
11
end of the rod and the end of the bit equals the desired
drilling depth.
3. Release the button to lock rod into position. When drilling
with the depth rod, stop when end of rod reaches surface
of material.
EnGLIsH
6 is fully charged.
and firmly pull the battery pack
on the
12
33