Bosch 06033B6000 Manual Original página 13

OBJ_BUCH-1988-003.book Page 13 Friday, June 10, 2016 8:33 AM
Noise/Vibration Information
Sound emission values determined
according to EN 60745-2-4.
Typically the A-weighted noise levels
of the product are
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector
h
sum) and uncertainty K determined
according to EN 60745:
a
h
K
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-4,
EN 50581.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ETM9,
70538 Stuttgart, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Bosch Power Tools
Assembly
 Before any work on the machine itself, pull the mains
plug.
Dust/Chip Extraction
 Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
dB(A) 83 86
as carcinogenic, especially in connection with wood-treat-
dB(A) 94 97
ment additives (chromate, wood preservative). Materials
dB 3 3
containing asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
2
m/s 6.0 7.0
Observe the relevant regulations in your country for the mate-
2
m/s 1.5 1.5
rials to be worked.
 Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Integrated Dust Extraction with Dust Box
(see Fig. A1 – A4)
Attach the dust box 4 onto the extraction outlet 11 until it
latches.
To empty the dust box 4, pull off the dust box downward.
Before opening the dust box 4, it is recommended to loosen
the dust from the filter element by gently striking it against a
firm support (as shown in the figure).
Grasp the dust box 4 by the recessed grip, fold the filter ele-
ment 3 upward and empty the dust box. Clean the thin plates
of the filter element 3 with a soft brush.
External Dust Extraction (see figure B)
Mount a vacuum hose 12 onto the extraction outlet 11. Con-
nect the vacuum hose 12 with a vacuum cleaner. An overview
for the connection of various vacuum cleaners can be found at
the end of these instructions.
The vacuum cleaner must be suitable for the material being
worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use a special vacuum cleaner.
Replacing the Sanding Sheet (see figure C)
When attaching a new sanding sheet, remove any dust or
debris from the sanding plate (e. g. with a brush).
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
The sanding plate is fitted with Velcro backing for quick and
easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheets, free the sanding plate
from any debris by tapping it in order to enable optimum ad-
hesion.
English | 13
1 609 92A 20F | (10.6.16)