Publicidad
12 | English
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Charging the Battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Removing the battery
The battery (1) is equipped with two locking levels to pre-
vent the battery from falling out if the battery release
button (2) is pressed unintentionally. As long as the battery
is inserted in the power tool, it is held in position by means
of a spring.
To remove the battery (1), press the battery release
button (2) and pull the battery out of the power tool. Do not
use force to do this.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
possible to check the state of charge when the power tool is
not in operation.
Press the button for the battery charge indicator or
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator, then the battery is defective and must be
replaced.
Battery model GBA 18V...
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
1 609 92A 6N4 | (10.06.2021)
Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Operation
Starting Operation
Inserting the Battery
Push the charged battery (1) into the base of the power tool
until the battery is securely locked.
Switching On and Off
To switch on the power tool, slide the on/off switch (3) for-
wards so that I appears on the switch.
To switch off the power tool, slide the on/off switch (3)
backwards so that 0 appears on the switch.
Changing the cutting direction
To change the cutting direction, the die holder (7) can be
turned to three positions, each offset by 90°. Cutting to-
wards the rear (towards the housing of the machine) is not
possible.
To turn the die holder (7), loosen the die holder screw (4)
until the die holder can be turned. Turn it 90° to the right or
the left in relation to the longitudinal axle of the power tool.
Make sure that the screw (4) engages in the drill hole of the
die holder (7). Tighten the screw.
Working Advice
Remove the battery from the power tool before carry-
u
to
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
This power tool is not suitable for bench-mounted use.
u
It must not be clamped into a vice or fastened to a work-
bench, for example.
Wear protective gloves during work. Sharp burrs de-
u
velop on the cut sheets; these can cause injury.
Exercise caution when handling the cutting chips. The
u
chips have sharp tips that can cause injuries.
Capacity
Apply the power tool to the workpiece only when switched
60−100 %
on. Always hold the power tool vertical to the surface of the
30−60 %
steel sheet and do not tilt it.
5−30 %
0−5 %
Capacity
80−100 %
60−80 %
40−60 %
20−40 %
5−20 %
0−5 %
Bosch Power Tools
Publicidad
