Intended Use - Stomer Professional SAD-10.8x2-LtD Instrucciones De Servicio

Cordless drill/driver

INTENDED USE

● This tool is intended for drilling in wood, metal, ceramic
and plastic; tools with electronic speed control and left/
right rotation are also suitable for screwdriving and
thread cutting
TECHNICAL SPECIFICATIONS
PRODUCT ELEMENTS
1 Switch for on/off and speed control
2 Switch for changing direction of rotation
3 Keyless chuck
4 Ring for torque control
SAFETY
WARNING! Read all instructions. Failure to follow all in-
structions listed below may result in electric shock, fi re and/
or serious injury.
● Ensure the switch is in the off position before inserting
battery pack. Inserting the battery pack into power tools
that have the switch on invites accidents.
● Recharge only with the charger specifi ed by the manu-
facturer. A charger that is suitable for one type of battery
pack may create a risk of fi re when used with another
battery pack.
● Use power tools only with specifi cally designated battery
packs. Use of any other battery packs may create a risk
of injury and fi re.
● Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
● Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the charger
(chargers with a rating of 230V or 240V can also be con-
nected to a 220V supply)
● In case of electrical or mechanical malfunction, imme-
diately switch off the tool or unplug charger from power
source
● SBM Group can assure fl awless functioning of the tool
only when original accessories are used
● Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
● This tool should not be used by people under the age of
16 years
● Be careful not to drill or drive into areas where electrical
wires may be contacted
● Ensure that switch (2) is in the middle (locking) position
before making any adjustments or changing accessories
as well as when carrying or storing the tool
● Do not touch the contacts in the charger
● Do not expose tool/charger/battery to rain
● Never charge battery outdoors
● Store tool/charger/battery in locations where tempera-
ture will not exceed 40° C or drop below 0° C
● Batteries will explode in fi re, so do not burn battery for
any reason
● When damaged, and under extreme usage and tem-
perature conditions, batteries may start to leak
- if liquid comes into contact with the skin, wash quickly
with soap and water, then with lemon juice or vinegar
8
1
2
- if liquid gets into the eyes, fl ush eyes with clean water for
a minimum of 10 minutes and seek immediately medical
attention
● When battery is not in tool or charger, it should be kept
away from metal objects such as nails, screws, keys etc.
to prevent short-circuit
● Do not use charger when damaged; take it to one of the
offi cially registered SBM Group Service Stations for a
safety check
● Do not use battery when damaged; it should be replaced
immediately
● Do not disassemble charger or battery
● Do not attempt to recharge non-rechargeable batteries
with the charger
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
● Do not connect the blue (= neutral) or brown (= live) wire
in the cord of the charger to the earth terminal of the plug
● If for any reason the old plug is cut off the cord of the
charger, it must be disposed of safely and not left unat-
tended
To ensure longer service life and proper perfor-
mance of the battery, take the following actions
when you start using new battery:
1. Use the new battery, without recharging it, till its com-
plete discharge.
2. Then charge the battery for 3-5 hours.
3. Repeat abovementioned actions (1 and 2) 3-5 times to
reach the nominal battery capacity.
MAINTENANCE
Make sure that the machine is not live when car-
rying out maintenance work on the motor.
Regularly clean the machine housing with a soft cloth, pref-
erably after each use. Keep the ventilation slots free from
dust and dirt.If the dirt does not come off use a soft cloth
moistened with soapy water. Never use solvents such as
petrol, alcohol, ammonia water, etc. These solvents may
damage the plastic parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please con-
tact your local SBM Group dealer.
ENVIRONMENT
In order to prevent the machine from damage during trans-
port, it is delivered in a sturdy packaging. Most of the pack-
aging materials can be recycled. Take these materials to
the appropriate recycling locations. Take your unwanted
machines to your local SBM Group dealer. Here they will
be disposed of in an environmentally safe way.
Li-Ion batteries can be recycled. Deliver them to a disposal site
for chemical waste so that they can be recycled or disposed of
in an environmentally friendly manner.