EINHELL PICOBELLA 18/215 Manual De Instrucciones Original página 25

reached and then place the brush on the sur-
face to be cleaned.
7. Guide the brush slowly and in lines, similar to
a broom, over the surface. Only apply a small
amount of pressure at fi rst and then increase
it little by little.
6.4.2 Cleaning wood, composite materials
(BPC/WPC)
Warning! Use only the SOFT brush to do this (to
fi t the brush, see section 5.5). All other available
brushes are made of hard material and can da-
mage the surface.
•
Always clean the boards or wooden elements
in a longitudinal direction (along the grain).
•
Actuate the left side (Fig. 18 / Item V) of the
changeover switch (forward). The equipment
will pull away from you (standard direction of
rotation).
•
It is recommended that you clean on a board-
by-board basis.
•
Afterwards, rinse the cleaned surface down
with water.
6.4.3 Cleaning smooth, unsealed paver and
stone surfaces
Note: Use the MEDIUM brush to do this (to fi t the
brush, see section 5.5).
•
Actuate the left side (Fig. 18 / Item V) of the
changeover switch (forward). The equipment
will pull away from you (standard direction of
rotation).
•
In case of certain kinds of stubborn dirt, it can
be helpful to clean using both directions of ro-
tation. Please note that when the equipment
is in reverse (changeover switch pressed on
the right, Fig. 18 / Item R), it has less power.
•
To clean perimeters and bases, remove the
wide side cover and clean them using the
side brush.
•
Afterwards, rinse the cleaned surface down
with water.
6.4.4 Rough, unsealed paving stones, con-
crete blocks and concreted surfaces
Note: Use only the ULTRA brush to do this (to fi t
the brush, see section 5.5).
Warning! There is a risk of injury from the bristles
of the metal brush – wear safety gloves.
•
Actuate the left side (Fig. 18 / Item V) of the
changeover switch (forward). The equipment
will pull away from you (standard direction of
rotation).
•
In case of certain kinds of stubborn dirt, it can
Anl_Picobella_18_215_SPK13.indb 25 Anl_Picobella_18_215_SPK13.indb 25
GB
be helpful to clean using both directions of ro-
tation. Please note that when the equipment
is in reverse (changeover switch pressed on
the right (Fig. 18 / Item R)), it has less power.
Afterwards, rinse the cleaned surface down
with water.
6.4.5 Brushing artifi cial turf
Warning!
•
Use only the SOFT brush to do this (yellow/
green). All other available brushes can dama-
ge the artificial turf.
•
Do not use water - dry-brush only.
•
Brush in a forward direction only (Fig. 18 /
Item V, standard direction of rotation - left side
of the changeover switch actuated).
•
Remove all leaves, rubbish and similar before
starting brushing.
1. Place the SOFT brush evenly on the surface.
2. Set the working height to the one which is
most comfortable for you (see section 5.3).
The splash guard must just clear the ground
on both sides.
3. Actuate the left side (Fig. 18 / Item V) of the
changeover switch (standard direction of ro-
tation).
4. Lift the equipment 1-2 centimeters and switch
on the equipment (see section 6.2).
5. Set the desired speed (from slow to fast) (see
section 6.3). Wait until the full speed has been
reached and then place the brush on the ar-
tifi cial turf. The equipment will pull away from
you.
6. To raise the fi bers upright, brush against the
direction of the fi bers of the artifi cial turf once
the desired speed has been reached. Do not
exert any pressure.
7. If required, draw the brush towards you and
let it roll away without pressure.
8. Repeat this movement until the desired result
has been achieved.
- 25 -
10.05.2023 08:51:42 10.05.2023 08:51:42