Publicidad
FR
Vous trouverez un choix complet de rallonges DMX certifiées IP65, de rallonges secteur certifiées IP65 et de câbles adaptateurs sur Internet, à
l'adresse www.cameolight.com.
ES
En la web www.cameolight.com encontrará los correspondientes cables de extensión DMX IP65, alargadores de alimentación IP65 y cables
adaptadores.
PL
Na stronie internetowej www.cameolight.com dostępny jest kompleksowy wybór przedłużaczy DMX, przedłużaczy sieciowych i kabli do
adapterów ze stopniem ochrony IP 65.
IT
Sul sito internet www.cameolight.com è reperibile un'ampia gamma di cavi di prolunga DMX IP65, cavi di prolunga di rete IP65 e cavi
adattatori.
OPERATION / BEDIENUNG / UTILISATION / OPERACIÓN / OBSŁUGA / UTILIZZO
EN
NOTE
When the projector is properly connected to the mains, the following information appears successively on the display during the startup process:
"Update Wait ..." (only for service purposes), "WELCOME TO cameo" and the software version "SOFTWARE V1.xx" . After this operation, the projec-
tor is ready for use and changes to the mode that was previously selected.
STATIC COLOUR (STATIC)
This mode offers the possibility to adjust the intensity of the warm white LED and a strobe effect. Press the MODE
button repeatedly until "STATIC" appears in the upper line of the display. Press ENTER and the cursor appears in
the bottom line of the display for the intensity. Now you can set the brightness of the warm white LED from 00 to
99 using the UP and DOWN buttons (example: W:00 = white at 0%, i.e. out. W99 = white at 100%, i.e. maximum
brightness). Confirm with ENTER.
The cursor will appear in the bottom line under the value of the flash frequency of the strobe effect and you can
activate the stroboscope effect using the UP and DOWN buttons and adjust the flash frequency from 00 to 99
(F00 = strobe deactivated, F01 = approx. 1 Hz, F99 = approx. 20 Hz). Confirm with ENTER.
SLAVE MODE (SLAVE MODE)
Press the MODE button repeatedly until "SLAVE MODE" appears on the display. Connect the DMX IN of the
slave to the DMX OUT of the master unit (same model). Now the slave unit follows the master unit.
DIMMER CURVE (DIMMER CURVE)
Press the MODE button repeatedly until "DIMMER CURVE" appears on the display. Press ENTER, and the cursor
appears in the bottom line of the display and then use the UP and DOWN buttons to select one of the 8 available
dimmer curves (DIMMER CURVE 01 - 08). Confirm with ENTER.
Dimmer curves 01 - 04: The light behaves in a manner similar to that of a halogen lamp with gentle changes in brightness.
Dimmer curves 05 - 08: The light reacts abruptly to changes in the DMX value.
Dimmer curves 01 / 05 linear: The light intensity increases linearly with the DMX value.
Dimmer curves 02 / 06 exponential: Adjustment of the light intensity is finer in the lower DMX value range and coarser in the upper DMX value range.
Dimmer curves 03 / 07 logarithmic: Adjustment of the light intensity is coarser in the lower DMX value range and finer in the upper DMX value range.
Dimmer curves 04 / 08 S-curve: Adjustment of the light intensity is fine in the lower and upper DMX value ranges and coarse in the middle DMX
value range.
linear
DMX value
SELECTING THE DMX MODE (DMX CH MODE)
Press the MODE button repeatedly until "DMX MODE" appears in the upper line of the display. Press ENTER, and
the cursor appears in the lower line of the display and then use the UP and DOWN buttons to select one of the
two DMX modes (01CH, 03CH). Confirm with ENTER.
You will find tables with the channels of the different DMX modes on the following pages of this manual.
DMX STARTING ADDRESS (DMX ADDR)
Press the MODE button repeatedly until "DMX ADDR" appears in the upper line of the display. Press ENTER, and
the cursor appears in the lower line of the display and then use the UP and DOWN buttons to select the desired
DMX start address between 001 and 512. Confirm with ENTER.
LOCK FUNCTION
To protect the projector against accidental and unauthorised operation, there is a possibility to lock the controls.
Press the UP and DOWN buttons simultaneously for 5 seconds.
The display now shows LOCKED and it is no longer possible to change the settings of the projector
using the control keys. To unlock, press the UP and DOWN buttons simultaneously for 5 seconds. Now the display
will change to the previously displayed information.
exponential
logarithmic
DMX value
DMX value
S-curve
DMX value
15
Publicidad
