Virutex LRB384 Manual De Instrucciones página 14

charging.
• Remove the battery 7 from the charger 19 and mount
battery 7 in the power tool.
Charger indicators (Fig. 12)
Charger indicators 21 and 22 inform of the battery 7
(Fig. 0) charging process. Signals of the indicators 21
and 22 are shown on the label 20. (Fig. 10).
• Fig. 12.1 - (The green indicator 22 is on, the battery
7 is not inserted in the charger 19) - the charger 19 is
connected to the power network (ready for charging).
• Fig. 12.2 - (The green indicator 22 is blinking, the
battery 7 is inserted in the charger 19) - the battery 7
is being charged.
• Fig. 12.3 - (The green indicator 22 is on, the battery 7 is
inserted in the charger 19) - the battery 7 is fully charged.
• Fig. 12.4 - (The red indicator 21 is on, the battery 7
is inserted in the charger 19) - the charging process of
the battery 7 is terminated due to inappropriate tem-
perature. When the temperature conditions are normal,
the process of charging will resume.
• Fig. 12.5 - (The red indicator 21 is blinking, the battery
7 is inserted in the charger 19) - the charging process
of the battery 7 is terminated because of its failure.
Replace the faulty battery 7, its further use is prohibited.
In the process of charging the battery 7 and the charger
19 become hot, it is a normal process.
8. STARTING THE MACHINE AND
ELECTRONIC ADJUSTMENT
To start the machine, move switch "B" to the right. Turn
button "A" to the desired working speed (Fig. 1).
9. MOUNTING THE BASE PLATES
MOBILE BASE SANDER SET WITH VELCRO DELTA PAD
8445498
VELCRO MOBILE BASE 8445189
To assemble the mobile base sander set with Velcro delta
pad ref. 8445498, first remove screw "F" and washer "G"
using service key "H" (Fig. 2). Next, remove the aluminium
base, along with pad "D", which is fitted (Fig. 2), and
attach the mobile base sander set with the Velcro delta
pad, using screw "F" and washer "G", as shown in (Fig. 3).
When the machine is fitted with the rotary orbital
base plate, follow the same procedure to assemble any
of the pads.
To attach the mobile base with Velcro accessory ref.
8445189, remove screws "C" (Fig. 2), remove standard
sanding pad "D" and attach the pad with the Velcro
accessory using screws "C".
VELCRO ROTARYORBITAL BASE 8445598
To attach this accessory, first remove screw "F" and
washer "G" using the service key "H" (Fig. 3). Remove the
14
aluminium base along with base "D" or "E" whichever
is installed at the time (Fig. 2 and 3) and take away the
4 aluminium columns pulling them out. As next step
insert base "I" (Fig. 5) and centre it using drag "J" (Fig.
4). Secure it in it's place with screw "F" and washer "G"
as indicated in (Fig. 5).
To install one of these bases when the machine is equipped
with the rotaryorbital plate, the procedure is the same.
10. INSTALLING SANDPAPER
ON THE 8402434 MOBILE BASE
Pinch the pincers "K" (Fig. 6) and insert the sandpaper
as indicated. It is important to ensure that the orifices
of the sandpaper coincide with those of the machine
base and that the sandpaper is perfectly taut on the
base. To perforate or centre abrasives, use accessory
8445232, ABRASIVE CENTRING-PERFORATING DEVICE.
ON THE 8445198 DELTA VELCRO MOBILE BASE
Velcro abrasives must be used with this type of base. To insert
sandpaper in the machine, proceed as indicated in (Fig. 7).
ON THE 8445498 ROTARYORBITAL BASE PLATE
Place the abrasive disk on the plate (Fig. 8) matching
the holes in the disk with those in the plate.
If the sandpaper does not have holes, they can be copied
from the holes in the plate.
11. CONNECTION TO AN EXTERNAL
SUCTION SOURCE
To connect the machine to the AS182K, AS282K aspirators
or to any other external suctioning source, install the
dust collection attachment (ref. 6446073 of 2.25 m or
1746245 of 5 m length) (optional accessory). To do so,
remove the suction bag "L" (Fig. 9) and fit nozzle "M" of
the dust collection attachment in its place.
The other end of the dust collection attachment is
connected to the external suctioning source of choice.
12. LUBRICATION AND CLEANING
The machine is shipped from factory completely lubri-
cated and does not require special care over the course
of its useful life. It is important to clean the machine
carefully after each use with a blast of dry air.
Keep the feed cable in perfect condition.
Keep all of the machine's ventilation and cooling ope-
nings clean and free from obstruction.
13. NOISE LEVEL AND VIBRATIONS
The noise and vibration levels of this device have been
measured in accordance with European standard EN
60745-2-4 and EN 60745-1 and serve as a basis for
comparison with other machines with similar applications.
The indicated vibration level has been determined for the
device's main applications and may be used as an initial
value for evaluating the risk presented by exposure to