Descargar Imprimir esta página

Black and Decker KW712-QS Traducción De Las Instrucciones Originales página 7

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 35
Electrical safety
#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Lock-off button
3. Shavings discharge outlet
4. Planing depth adjustment knob
5. Planing depth graduation
Assembly
Warning! Before assembly, make sure that the tool is switched off
and unplugged.
Replacing the cutting blades (fig. A)
The cutting blades provided with this tool are reversible.
Replacement cutting blades can be obtained from your local
retailer.
Removing
Loosen the bolts (6) using the spanner supplied.
u
Slide the blade (7) out of the holder.
u
Reverse the blade so that the unused side comes in position.
u
If both sides are worn, the blade must be replaced.
Fitting
Slide the blade into the holder until it is against the end stop.
u
Tighten the bolts using the spanner supplied.
u
Warning! Always replace both cutters.
Adjusting the depth of cut (fig. B)
The depth of cut is indicated by the marking (8). The setting
range can be read from the graduation (5).
Turn the planing depth adjustment knob (4) to the required
u
depth of cut.
Turn the knob to the 'P' postion whenever the tool is not in
u
use.
KW712KA Fitting and removing the parallel fence
(fig. C)
The parallel fence is used to for optimum control on narrow
workpieces.
Loosen the locking knob (9).
u
Insert the parallel fence (11) through the opening (10).
u
Slide the parallel fence into the desired position.
u
Tighten the locking knob.
u
To remove the parallel fence proceed in reverse order.
u
Connecting a vacuum cleaner to the tool (fig. D)
An adaptor is required to connect a vacuum cleaner or dust
extractor to the tool. The adaptor can be purchased from your
Slide the adaptor (12) over the shavings discharge outlet (3).
u
Connect the vacuum cleaner hose (13) to the adaptor.
u
Assembling and fitting the shavings collection bag
(fig. E)
The shavings collection bag is particularly useful when working
in confined spaces.
local BLACK+DECKER retailer.
Before first use, you will have to assemble the shavings
collection bag.
Fit the wire frames (14) to the connecting plate (15) using
u
the screws (16) and washers (17).
Pull the cloth bag (18) over the frame structure as shown.
u
Take care that the elasticated mouth (19) is well fitted
around the edge of the connecting plate (15).
Slide the connecting plate over the shavings discharge
u
outlet (3).
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving
u
parts.
Injuries caused when changing any parts, blades or
u
accessories.
Injuries caused by prolonged use of a tool. When
u
using any tool for prolonged periods ensure you take
regular breaks.
Impairment of hearing.
u
Health hazards caused by breathing dust developed
u
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Use
Warning! Let the tool work at its own pace. Do not overload.
Adjust the depth of cut.
u
If necessary, fit and adjust the parallel fence.
u
ENGLISH
7

Publicidad

loading

Este manual también es adecuado para:

Kw712kaKw712