Adler europe AD 7049 Manual De Uso página 7

19. Do not direct the suction tube of the vacuum cleaner towards other people or animals.
20. Only vacuum dry surfaces.
21. Use only accessories intended for this device.
22. Be especially careful when vacuuming the stairs, take care of your own safety.
23. Do not block any ventilation openings.
24. Do not run the vacuum cleaner without the filter in place.
25. Do not pull the vacuum cleaner by the hose.
26. Be careful that the power cord is not caught in a door or jammed. Pay attention to the
length of the power cord when moving the vacuum cleaner. Sudden pulling of the vacuum
cleaner with a taut cable may damage it.
26. Do not vacuum dust and construction residues, residues of this type of contamination
immediately void the warranty.
27. Do not leave the device unattended during operation.
28. Always unplug the appliance when left unattended and before assembling,
disassembling or cleaning.
29. Before removing the plug from the socket, always switch off the device with the button.
Device description Vacuum cleaner:
1. Handle 2. Tube
6. Cable hanger Up 7. Cable
10. Cable hanger down 11.Container release button
14. Round brush
Before first use:
1. Remove all packing material from the device.
2. Assemble the device as shown on page picture 2A by pushing the tube into the handle. The little button on the handle should appear
in the hole in the handle.
Note ( The device can also be used without the Tube (2) and used as a car vacuum with only the attachments and used by the handle.)
3. Insert the floor brush (13) into the hole in the dust container (12) as shown in picture 4A.
4. Unroll the power cable (7).
5. Plug the power cable into the wall socket.
6. Turn on the device by pressing the On / Off button (5).
Changing the attachments:
1. Remove the floor brush (13).
2. insert the connector (16) into the dust container (12). As shown in picture 5A.
Opening the dust container:
1. Press and hold the button on the side of the dust container.
2. Twist the dust container clockwise by holding the dust container with one hand and the other hand firmly placed on the body of the
device or handle.
3. On the side of the device are drawn 2 symbols of a lock. One is open and one is closed. Move the container until it the marker is
aligned with the open lock.
4. Pull the dust container downwards and empty the dust container into a waste bin.
5. Put the container back and twist counterclockwise so the marker and closed lock symbol align.
Cleaning the HEPA filter.
1. Open the dust container as explained in the instructions above.
2. Twist the HEPA filter counterclockwise a quarter turn to release it from the mounting. As shown in picture 8A.
3. Clean the HEPA filter with air pressure or by gently tapping it against a waste bin.
4. You can also clean it under running water. After washing it with water let it air dry in a warm place with a lot of air circulation.
WARNING: DO NOT USE ANY SOAP OR CHEMICAL CLEANER. ONLY USE CLEAN TAP WATER. DO NOT SCRUB OR USE ANY
ABRASIVE CLEANING METHODS.
5. Assemble the filter back into its mounting.
NOTICE: AFTER SOME TIME AND WASHING THE EFFICIENCY OF THE HEPA FILTER WILL DROP. PLEASE MAKE SURE TO
EXCHANGE THE HEPA FILTER REGULARLY. NOT DOING SO WILL LEAD TO A DROP IN SUCTION POWER, OVERHEATING,
AND DAMAGING THE DEVICE.
TECHNICAL DATA
Power source: 220-240 V ~ 50 Hz
Power: 600 W Max: 800W
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste
bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may
effect the environment. Do not dispose this appliance in the common waste bin.
3. Handle release button
8. Plug
12. Dust container
15.Nozzle
7
4. Body 5. On / Off button
9. Air outlet
13. Floor brush
16.Connector