Woods WAC1204G Manual De Instrucciones página 16

Operating Instructions
GB
FUNCTION OF THE OPERATION MODES AND INSTALLATION DESCRIPTIONS
Installation
If the unit has been transported horizon-
tally, keep it in an upright position for 4
hours before using it.
Place the unit on a flat and solid surface.
Do not install the unit in bathrooms or
other wet environments.
Make sure that airflow isn't blocked, always
keep at least 50 cm distance to surroun-
ding surfaces.
INSTALLING THE EXHAUST HOSE
1. Extend one end of exhaust hose,
screw the end without a slot of round
connector onto it with anticlockwise
direction at least 3 laps.
2. Extend another end of exhaust hose,
screw the adapter onto it in a counter-
clockwise direction at least 3 laps.
3. Extend the exhaust hose and lead it
outside through a door or window.
USING THE WINDOW KIT
1. To use the window kit, open the
window and place the window kit either
horizontally or vertically, depending on
the window.
2. Adjust the length of the window kit and
fasten it with the screws.
3. Shut the window and attach the adapter
on the exhaust hose to the window kit.
BATTERY INSTRUCTIONS
Before using your remote, install the AAA
batteries into the remote control.
1. Press and slide the battery cover on the
back of the remote control, then you can
remove the cover.
2. Insert two new alkaline AAA batteries
into the battery compartment, being
sure to note the proper polarity.
3. Put back the battery cover, making sure
the locking tab clicks into place.
Use alkaline batteries only. Do not use
rechargeable batteries.
When replacing batteries, always replace
both batteries with new ones. Do not mix
old and new batteries.
16
If the air conditioner will not be used for
an extended period of time, remove the
batteries from the remote control.
Operating instructions
1. Starting the unit. Press the POWER
button to start and stop the unit.
2. Select mode. The unit has 4 different
modes: cooling, dehumidify, energy
conservation and fan mode. Press MODE
on the control panel or remote control
to select mode.
• Cooling mode: the set desired
temperature with the arrows on the
control panel or the remote control. Set
temperature is shown in the display.
• Dehumidify. In dehumidify mode,
the fan will run on low speed only.
Temperature cannot be set.
• Fan mode. The compressor stops and
only the fan will run. Temperature
cannot be set.
• Energy conversation mode. Low
energy consumption under Energy
Conversation mode. When the ambient
temperature is higher than the set
temperature, the unit operates in cool
mode. When the ambient temperature
reaches the set temperature, the
compressor stops running and the
upper fan also stops running. After 2
minutes and 30 seconds, the upper fan
will run at low speed for 30 seconds. If
the compressor does not start (that is,
the ambient temperature is lower than
the set temperature), the upper fan will
repeatedly operate in this mode (stop
for 2 minutes 30 seconds / low wind
operation for 30 seconds).
3. Set timer.
• To set the timer for shut off, press
the TIMER button when the unit is
operating.
• To set the timer for start, press the TIMER
button when the unit is switched off.
Set time with the up and down arrows on
the control panel or remote control. When
the timer is activated, a light is shown on
the control panel.
4. Set fan speed. Press the SPEED button
on the control panel to choose fan
speed. On the remote control, press the
FAN button to choose fan speed.
5. Celsius/Fahrenheit On the control panel,
press the up and down arrows at the
same time to switch between Celsius
and Fahrenheit.
6. Sleep mode. Use the sleep mode during
the night and the unit will not disturb
your sleep. When in cooling mode, press
the TIMER and UP together to enter
sleep mode. On the remote, press the
SLEEP button. Press again to deactivate.
7. Auto swing function. Press the TIMER
and SPEED buttons at the same time
to activate the swing function. On the
remote, press the Auto-swing button.
Press again to deactivate.
8. Auto clean function. Press the AUTO-
CLEAN button on the remote control to
clean the unit internally. The unit will
clean for 3 minutes before shutting off.
PROTECTION FUNCTIONS
Automatic defrost
The unit will automatically defrost when
needed. In defrost mode, the display
shows E4 and no buttons except the
POWER button are active.
Compressor protection
The unit has a compressor protection
function causing a 3-minute start delay
after the unit is restarted.
Water full alarm
When the water tank is full, the unit will
stop working. A water-full indication light
is shown in the display and a warning
sound is heard. Empty the water tank and
restart the unit.