Byox TORNADO Instrucciones De Uso página 10

5.Step 5 – See Figure 5: In order to attach the rear wheels, take the rear axles and thread each one of them through the
openings in the middle of the rear wheels → the opening for the rear brake(Q) → the opening in the rear part of the frame
(А). Tighten the axle using a nut as shown.
6.Step 6 – See Figure 6: To attach the small foot rest (M) to the tricycle frame (A), first you need to remove the screws from
the foot rest. Remove the plastic cover from the frame. Place the footrest on the frame and align the screw openings. Slide
the screws through those openings and tighten them.
7.Step 7 – See Figure 7: Take both of the seat parts – G1 & G2. Align the openings of these parts, which are intended for
the fixing screws. Slide the screws through these openings and tighten them using a hexagram.
8.Step 8 – See Figure 8: Attach the assembled seat to its base on the tricycle frame. Slide the long fixing screw through the
opening in the bottom of the tricycle and then from the opening in the seat. Tighten the screw in order to fix the seat.
9.Step 9 – See Figure 9: Attach the soft seat pad to the plastic backrest and the seat. Slide each parts of the safety belt
through the openings in the backrest and seat. Fix them using the C – shaped plastic fixators. Connect the plastic ends of
the shoulder belts to the crotch buckle.
10.Step 10 – See Figure 10: Place the foot rest (P) to the seat (G). Tighten using the plastic screws.
11.Step 11 – See Figure 11: Connect the visor to the canopy. Attach the canopy to the backrest – the plastic side holders of
the canopy must be attached to the rails of the backrest.
12.Step 12 – See Figure 12: Connect the parent control handle (J) to the tube at the bottom of the frame. Put the red
bracket ]in closed position. This way you will fix the parent control handle to the frame.
13.Step 13 – See Figure 13: Finally, place the bag on the handle and attach the rear basket to the frame under the parent
control handle.
PRODUCT FUNCTIONS
1.Free Wheel Function – See Figure U1 – turn the red button clockwise or counter clockwise in order to activate/
deactivate this function. When this function is active, if your child turns the pedals, they will not move the front wheel and you
can freely guide the movement of the tricycle using the handle.
2.Rear brakes – See Figure U2 – press them down to fix the rear wheels, when you do not use the tricycle.
3.Adjustable backrest – See Figure U3 –Press the red buttons on each side of the backrest in order to recline it or to put it
in a straight position.
4.Adjustable canopy – See Figure U4 & U7:
-U4 – The canopy is with several sections. If there is no need it to be fully stretched, fold one section by attaching the small
belt on the top of the canopy to the small buckle.
-U7 – Recline the canopy backwards slightly by pressing the side plastic holders.
5.360° Rotating seat – See Figure U5 – Lift the big footrest. In the base of the seat you will find the red button "PULL". Pull
it towards you and holding it pulled turn the seat in 180° so that your child is facing you. Lower the footrest. After that pull up
the red button of the handlebar and in the same time fold the handlebar. Place the backrest in the most reclined position,
6.Adjustable parent control handle – See Figure U6 – In order to lift up or lower it – press the pop – up buttons at the
back of the handle and place the handle in the desired position. Make sure the buttons are fixed in the corresponding
openings before using the tricycle.
7.Footrests –The tricycle is supplied with 2 footrests. Bigger one for smaller children, which you can remove when the child
is bigger and can reach the pedals. The smaller footrest is for bigger children. The tricycle can be used without the canopy,
backrest and the parent control handle. In these cases you should fold the smaller footrest. Fold the black rests to the tube
of the foot rest. After that press and slide down the black plastic button in the base of the tube and fold the foot rest to the
tricycle frame. Or you can take off the foot rest using a screwdriver.
8.Music tray – See Figure U8 – The tray is supplied with button for various melodies and button for lights. Use 3 not
rechargeable alkaline 1,5V AA batteries in order to activate the music/ light functions.
PLACING THE BATTERIES AND IMPORTANT INFORMATION
WARNING! When placing the batteries, children should not be present!
1.The batteries are not included in the set.
2.After that place 3 x AA 1.5 V batteries in the compartment, make sure that you observe the respective polarity (+/-) when
you place them, it is indicated on the scheme "BATTERY CHANGE" and also at the bottom of the compartment.
3.Replace the cover of the battery compartment and secure it with the screw.
4.The batteries should be handled by an adult only. Do not allow the children to play with the batteries.
5.Always remove the discharged batteries and do not throw them away with the household waste, use the places designated
for that purpose. They are recyclable.
6.Use АА batteries only.
7.Alkaline batteries are recommended.
8.Always remove the batteries, if you will not use the product for a long period of time.
9.When you replace the batteries always replace them with new ones, always replace all batteries. Children should not be
present while you are replacing the batteries.
10.Do not mix old batteries with new ones.
11.Do not mix alkaline, standard (Carbon - Zinc), or rechargeable (Nickel – Cadmium) batteries.
12.Do not throw the batteries in fire, because they may blow up or leak.
9