Publicidad
Idiomas disponibles
Idiomas disponibles
SAITEK 4-IN-1 VIBRATION WHEEL
Features
•
Compatible with PC, PS2/PS3 and Xbox
•
Button settings programmable when using PC and PS2
•
Detachable lap rest for complete comfort and control when playing from your sofa
•
Removable clamp locks the wheel in place when sat at a desk
•
On-the-fly sensitivity adjustment helps you adapt to different driving games
•
Use the included pedals or wheel paddles to accelerate and brake, depending on your playing
environment
Setting up your controller
1
Attach the main wheel unit to the desk clamp or lap support.
3
If using the desk clamp, position the wheel unit on the edge of your desktop, and turn the
clamp grip clockwise until the unit is securely attached to the desk. Do not overtighten!
4
Plug the PS/2 cable from the pedal unit into the socket in the wheel unit, making sure the
connector clicks firmly into place.
5
Place the pedal unit on the floor in your preferred driving position.
System Compatibility
PC running Windows XP/Vista (32-bit only), PS2/PS3 and Xbox
Software installation for PC
1.
With your computer switched on, close down any programs that are currently running and
insert the Installation CD into your CD-ROM drive.
2.
When the Introduction Screen appears, click Install Software to continue. If the CD does not
run automatically, select Start from the Windows® Taskbar, then Run and type D:\Setup.exe
and click OK - where D:\ is letter of your CD-ROM drive. For Vista users, the screen will ask
Do you want to run this file? Press Run. A screen will now appear saying A program needs
your permission to continue. Press Continue.
3.
When the Welcome screen appears, click Next to continue.
4.
After reading the Disclaimer, select the I accept the terms of the Disclaimer option and click
Next to continue.
5.
Plug the USB cable into one of your computer's USB ports and click on Next.
6.
At the Registration screen, select Check this box to register now and follow the on-screen
instructions, or you can choose to select this option later.
7.
Click on Finish to complete the installation.
Installation for users of PS2 and Xbox
Plug the wheel's PS2 or Xbox controller cable into one of your console's free controller sockets.
Installation for users of PC or PS3
Plug the wheel's USB cable into one of your PC or PS3's free USB ports.
Mode switching
The 4-in-1 Vibration Wheel supports both Digital and Analog modes on PS2. Press the Mode
button to switch modes.
Vibration Force Feedback
The 4-in-1 Vibration Wheel offers vibration force feedback with PS2. Press the Select and Up
buttons to switch the force feedback on or off.
Auto calibration
To calibrate the wheel, press the Mapping button for two seconds and the red LED will blink quickly
to show the wheel is calibrating.
Sensitivity adjustment
The 4-in-1 Vibration wheel has six sensitivity settings. Normal setting is three.
To adjust sensitivity press the Select and Right buttons. Each time you press the two buttons, the
stick sensitivity will increase by one increment until it reaches six and then start from one again.
So, if you want to reduce sensitivity from normal setting (three) to one, press the Select and Right
buttons four times: 4, 5, 6, 1.
Button programming
1
Press and hold the Select button for 3 seconds to enter programming mode - the red LED will
blink quickly. Press the button that you want to change and the red LED will stop blinking. Now
press the desired function - the LED will blink quickly after programming is completed (PS2
only)
2
The 1, 2, 3, 4, 5, 6, 7, 8, RY and RY buttons all can be programmed when using a PC. Gas
Pedal, Brake Pedal, L-hand, R-hand, L1, L2, R1, R2, SL, ST,
programmed when using a PS2.
Exiting program mode:
The wheel will automatically exit programming mode after 6 seconds or press the Select button to
leave programming immediately.
Resetting button programming
Press and hold the Mode button for 2 seconds to reset all button programming.
O
,
, X and
can all be
Publicidad
