Publicidad
Idiomas disponibles
Idiomas disponibles
container in advance to block foam in the juice) (Picture H1. Page 5)
Place residue container below the frame residue outlet, near the juice container. (Picture H2. Page 5)
Mount tray onto the upper end of inlet cylinder.
The tray facilities loading of food material, such grape or strawberry.
Connect to power supply and get ready for startup. (Before connecting the device into mains power, make sure the switch is in Off
position.)
Clean the material and cut it into pieces small enough to pass through the inlet, and place them onto the tray.
WARNING:
Any hard core, seed, skin or shell should be removed in advance. As it might get stuck in the device or block the juice extraction holes.
Press down the ON button to start then press R button to reverse. Then Press the On button again to start and keep the machine
operating for less than 10 minutes.
Do not to touch the power switch with wet hand to avoid electric shock, leakage or fire.
Load the food material in through the inlet and push them in with the attached food pusher. DO NOT USE ANY METAL UTENSILS OR
OTHER OBJECTS INSTEAD OF THE ATTACHED PUSHER.
Proper amount of force shall be used to push the food material in, not excessive but sufficient to have it cut off exactly.
(Do not put your finger or any other object into the inlet! If the residue/juice container is full, disconnect the power supply and empty and
then clean before restart.）
Upon completion, shut down the device by pressing the ON/OFF switch and when no juice flows out of the outlet, disconnect the power
supply.
The extracted juice should be drunk as soon as possible. The longer the juice is exposed to air and sun the less nutritious it will be.
The remaining pulp should be disposed as fast as possible. Either by throwing it away or it can be dried and used as an fiber
supplement. For example apple pulp can be used in baking or making pastries as it has the intense flavor of apples and will not release
water and juices into the dough.
Do not to touch the power switch with wet hands to avoid electric shock, leakage or fire.
MEAT GRINDER (Only AD4131)
Assemble the feeding tube
Embed the feeding tube into the frame by aligning the center on the inlet with the triangle mark (to point at the three fasteners on the
extractor).
Then rotate the feeding tube counterclockwise till it clicks. (Picture I. Page 6)
Align the hexagonal shaft of feeding screw with the hole in the frame and push it in to the end. (slightly rotate the spiral propeller to make
good alignment) (Picture J. Page 6)
Put the cross knife onto the feeding screw(there is a 4 angles shape on the front point of feeding screw to place the cross knife. (Picture
K. Page 6)
Put the cutting disc on the feeding screw after placing the cross knife. (Picture L. Page 6)
Screw the fixing ring on the feeding tube to fix the parts of feeding tube accessory.
Put the food tray onto the top of feeding tube
Put the pusher onto food tray, finish the meat grinder function preparation.
Plugged in, prepare for working. Make sure product is on switch-off mode.
Press down ON button to to work.press R button to reverse. start and keep the machine operating for less than 10 minutes.
Do not to touch the power switch with wet hand to avoid electric shock, leakage or fire.
Making sausage (Use minced meat to make sausage)
(Please use picture M. Page 6 as an example of correct assembly order):
1. Prepare the minced meat
2. Remove the fixing ring and put the kebbe attachment & sausage tube, then screw the fixing ring to fix the parts again.
3. Connect the sausage wrapper on the sausage tube. Put the minced meat onto feeding tube, then the minced meat will be filled into
sausage wrapper. Sausage ready.
Vegetable Slicer (Only model 4131)
Put the salad maker into the machine, and rotate the locking ring clockwise to lock the salad maker device onto the machine. (Picture N.
Page 7)
Lift up the cover of the salad maker, then select the drum that needs to be used and place it inside the salad maker. (Sometimes it will be
advised to move the drum left and right to make the hexagonal screw to fall into proper position before moving to the next step) (Picture
O. Page 7)
Press the lid downwards and apply slight force to ensure that the lid of the salad maker drum is tightly fastened.
Make sure the On / Off switch is in Off position.
Plug the device into mains power.
Press down ON button to turn on the device then press press R button to reverse to make sure the parts are correctly assembled.
Start and keep the machine operating for less than 10 minutes.
Do not to touch the power switch with wet hand to avoid electric shock, leakage or fire.
Place the food into the salad maker tube, and use the pusher to push the food into the salad maker tube.
Pull out the power plug and put the machine in a power off state.
Lift up the cover of the salad maker tube.
Take out the drum. (Picture P. Page 7)
10
Publicidad
