DeWalt D51431 Manual De Instrucciones página 6

Compressor will be sufficient for tools at all production rates.
Le compresseur peut actionner tout outil, quel que soit le taux de production.
El compresor será suficiente para las herramientas a todo índice de producción.
Compressor will be sufficient at slow or moderate production rates, but may have difficulty at very rapid rates.
Le compresseur peut actionner des outils à des taux de production faibles ou modérés, mais peut avoir de la difficulté à
des taux très élevés.
El compresor será suficiente a índices de producción lentos o moderados pero tendrá dificultad con índices demasiado rápi-
dos.
Compressor will be adequate only when tools are utilized at slow production rates (punch-out or occasional use).
Le compresseur ne sera vraiment efficace que lorsque les outils sont utilisés à de faibles taux de production
(p. ex., lors de travaux rapides ou occasionnels).
El compresor será adecuado sólo cuando las herramientas sean utilizadas a índices de producción lentos
(perforación o uso ocasional).
Not Recommended
Taux non recommandés
No se recomienda
CARACTÉRISTIQUES DES ATTACHES
ESPECIFICACIONES PARA GRAPAS
Fastener Lengths
Longueur
Largos de grapas
Fastener Gauge
Calibre
Calibre de grapas
Crown Width
Largeur de tête
Ancho de la cabeza
Fastener Stick Angle
Angle du bâton
Ángulo de grapas
MANY COMMON PROBLEMS CAN BE SOLVED EASILY BY UTILIZING THE CHART BELOW. FOR MORE SERIOUS OR PERSISTENT PROBLEMS,
Trigger valve housing leaks
Top cap leaks air
Exhaust leaks
Air leaks around nose when
tool is at rest. (Driver blade in up position)
Air leaks around nose when tool is in
actuated position. (Driver blade in
down position)
Tool does not cycle in cold weather
Lack of power; sluggish
Skipping fasteners; intermittent feed
Fasteners jam in tool
FASTENER SPECIFICATIONS
D51430
1" - 2"
(25.4 mm - 50.8 mm) (25.4 mm - 50.8 mm)
de 25,4 mm – 50,8 mm de 25,4 mm – 50,8 mm
(1 à 2 po)
1 – 2 pulg.
(25,4 mm – 50,8 mm) (25,4 mm – 50,8 mm)
16 gauge
16
Calibre 16
7/16"
11,2 mm (7/16 po) 13 mm (1/2 po)
11,2 mm (7/16 pulg.) 13 mm (1/2 pulg.)
Straight
Droit
Recto
CARACTÉRISTIQUES DE L'OUTIL
ESPECIFICACIONES DE LA HERRAMIENTA
Height / Hauteur /Altura
Width / Largeur / Ancho
Length / Longueur / Largo
Weight / Poids / Peso
Recommended Operating Pressure
Pression d'utilisation recommandée
Presión de operación recomendada
Air Consumption per 100 cycles
Consommation d'air par 100 cycles
Consumo de aire por cada 100 ciclos 3.9 scfm @ 100 psi (0,11 scmm a 6,9 bar)
Loading capacity
Capacité de charge
Capacidad de carga
Troubleshooting Guide
CONTACT A DEWALT SERVICE CENTER OR CALL 1-(800)-4-DEWALT.
DISCONNECT AIR FROM TOOL BEFORE ALL REPAIRS
O-ring or valve stem failure
Loose cap screws
Damaged or worn gasket or o-ring
Main seal or o-ring damaged, debris in tool.
Damaged or worn o-rings
Damaged or worn bumper
Tool not receiving air
Valve may be frozen
Damaged or worn o-rings
Broken or damaged driver blade
Low air pressure
Lack of lubrication
Damaged or worn o-rings
Exhaust port blocked or clogged
Air restricted
Lack of lubrication
Nosepiece screws loose
Wrong size/angle fasteners
Dirty magazine
Worn magazine
Broken or damaged driver blade
Trigger valve o-ring worn or damaged
Worn piston o-ring
Worn or damaged pusher spring
Magazine loose
Driver channel in nose piece worn
Wrong size/angle fasteners
Magazine loose
Worn driver blade
Nosepiece screws loose
Fasteners not feeding properly
D51431
1" - 2"
(1 à 2 po)
1 – 2 pulg.
16 gauge
16
Calibre 16
1/2"
Straight
Droit
Recto
TOOL SPECIFICATIONS
D51430 16 GA. Medium Crown Stapler
D51430, Agrafeuse pour agrafes à tête moyenne,
calibre 16
D51430 Engrapadora de calibre 16 para
grapas de cabeza mediana
11.0'' (279.4 mm) / 279,4 mm (11,0 po) / 11,0 pulg. (279,4 mm)
3'' (76.2 mm) / 76,2 mm (3 po) / 3 pulg. (76,2 mm)
14.75'' (374.7 mm) / 374,7 mm (14,75 po) / 14,75 pulg. (374,7 mm)
4.5 lbs. (2.04 kg) / 2,04 kg (4,5 lb) / 4,5 lb (2,04 kg)
70 - 120 psig (4.9 - 8.3 bar, 5 to 8.5 kg/cm
2
de 5 à 8,5 kg/cm (70 à 120 lb/po
70 - 120 psi (4,9 – 8,3 bar, 5 a 8,5 kg/cm
3.9 scfm @ 100 psi
3.9 scfm @ 100 psi (0,11 scmm a 6,9 bar)
Up to 160 fasteners
Jusqu'à 160 attaches
Hasta 160 grapas
Replace valve using: Trigger Valve Kit: Cat.# D510005
Tighten cap screws using appropriate Allen wrench
Replace gasket/o-rings using: O-ring Repair Kit, Cat. # D514301
Replace gasket/o-rings using: O-ring Repair Kit, Cat. # D514301
Replace gasket/o-rings using: O-ring Repair Kit, Cat. # D514301
Replace bumper using: Bumper Kit, Cat. # D514303
Check air supply
Warm up tool
Replace gasket/o-rings using: O-ring Repair Kit, Cat. # D514301
Replace Driver Blade Kit: Cat. # D514302, D514312
Check air supply
Lubricate tool using approved pneumatic tool oil.
Replace gasket/o-rings using: O-ring Repair Kit, Cat # D514301
Disconnect air, remove exhaust plate from top of tool, clean port
Check air supply and couplers
Lubricate tool using approved pneumatic tool oil
Tighten nosepiece screws using appropriate Allen wrench
Use only recommended fasteners
Clean magazine track and nosepiece
Replace magazine
Replace Driver Blade Kit; Cat. # D514302, D514312
Replace valve using: Trigger Valve Kit; Cat. # D510005
Replace piston o-ring using: O-Ring Repair Kit, Cat.# D514301
Replace spring
Check that magazine latch is holding firmly
Replace nosepiece
Use only recommended fasteners
Check that magazine screws are holding firmly
Replace Driver Blade Kit; Cat # D514302, D514312
Tighten nosepiece screws using appropriate Allen wrench
Ensure fasteners are feeding properly into nose
Portable
Handcarry
3.2 - 4 CFM
Petit
outil
portatif
5,4 – 6,8 CMM
(3,2 – 4 CFM)
Portátil
5,4 – 6,8 CMM
(3,2 – 4 CFM)
1
2
3
4
5
6
7
8+
2
)
2
ou 4,9 à 8,3 bar)
2
)
Industrial
5.5 HP Gas 8 HP Gas
23+ CFM
14 - 16
2 HP Elec.
CFM
8 - 9 CFM
Outil à gaz
Outil à gaz
Outil indus-
(5,5 hp)
(8 hp)
triel
Outil élec-
23,8 – 27,2
39,1+ CMM
trique
CMM
(23+ CFM)
(2 hp)
(14 – 16
CFM)
13,6 – 15,3
CMM
(8 - 9 CFM)
Industrial
8 HP Gas
39,1+ CMM
5,5 HP Gas 23,8 – 27,2
(23+ CFM)
2 HP Elec. CMM
(14 – 16
13,6 – 15,3
CFM)
CMM
(8 - 9 CFM)