Publicidad
Idiomas disponibles
Idiomas disponibles
and the products that you use. The transmission may
also be cut off or may get disconnected depending
on the radio wave conditions, DECT phones or any
other WLAN 11b appliances. The standard values of
the transmission speed are the theoretical maximum
values for the wireless standards. They are not the
actual speeds of data transmission.
The location where the transmission is most effective
differs depending on the usage environment.
The TV supports 802.11 a, b, g & n type modems. It
is highly recommended that you should use the IEEE
802.11n communication protocol in order to avoid any
possible problems while watching videos.
You must change your modem's SSID when there are
any other modems around with the same SSID. You
can encounter connection problems otherwise. Use a
wired connection if you experience problems with a
wireless connection.
Configuring Wireless Device Settings
To configure wireless connection settings go to the
Settings>Network menu.
Network Type
Set Network Type as Wireless Device to start
connection process.
Scan Wireless Networks
Highlight Scan Wireless Networks option and press
OK to start a search for available wireless networks.
All found networks will be listed. Highlight your desired
network from the list and press OK to connect. A
network with hidden SSID can not be detected by
other devices. If you want to connect to a network with
hidden SSID, scroll down the list of detected wireless
networks, highlight the Add New Network option and
press OK. Enter the name of the network and select
the security type using the related options to connect.
Note: If the modem supports N mode, you should set N
mode settings.
If the selected network is password-protected, enter
the correct key by using the virtual keyboard. You can
use this keyboard via the directional buttons and the
OK button on the remote control.
Wait until the IP address is shown on the screen. This
means that the connection is now established.
Disconnect
If you have connected to a wireless network Dis-
connect option will appear in the Network menu and
your wireless network profile will also be saved, thus
your TV will connect to the same network automati-
cally whenever you switch to wireless connection. To
disconnect from a wireless network and delete the
saved wireless network profile, highlight Disconnect
and press OK.
Press WPS on your wifi router
If your router has WPS, you can directly connect to the
modem/router without entering a password or adding
the network first. Highlight Press WPS on your wifi
router option and press OK. Go to your modem/router
device and press the WPS button on it to make the
connection. You will see a connection confirmation on
your TV once the devices have paired. Select OK to
proceed. No further configuration is required.
Internet Speed Test
Highlight Internet Speed Test and press the OK button
to check your internet connection speed.
Advanced Settings
Highlight Advanced Settings and press the OK button
to open the advanced setting menu. Use directional
and numeric buttons to set. The procedure is the same
as explained for wired connectivity. Highlight Save and
press the OK button to save settings when complete.
Networked Standby Mode
You can enable or disable the Networked Standby
Mode feature by setting this option accordingly. Refer
to Networked Standby Mode section for further
information.
Other Information
The status of the connection will be displayed as
Connected or Not Connected and the current IP
address, if a connection is established. The MAC
address of your TV will also be displayed on the screen.
Connecting to your mobile device via WLAN
• If your mobile device has WLAN feature, you can
connect it to your TV via a router, in order to access
the content in your device. For this, your mobile
device must have an appropriate sharing software.
Connect your TV to your router by following the steps
mentioned in the sections above.
Afterwards, connect your mobile device to the router
and then activate the sharing software on your mobile
device. Then, select files that you want to share with
your TV.
If the connection is established correctly, you will
be able to access the shared files installed on your
mobile device via the Audio Video Sharing feature
of your TV.
Highlight the Audio Video Sharing option in the
Sources menu and press OK, available media server
devices in the network will be displayed. Select your
mobile device and press the OK button to continue.
• If available, you can download a virtual remote
controller application from the server of your mobile
device application provider.
Note: This feature may not be supported on all mobile
devices.
English - 32 -
Publicidad
