Publicidad
Idiomas disponibles
Idiomas disponibles
EN
Disclaimer
By using this product, you signify that you have read, understand, and accept the terms and
conditions of this guideline and all instructions at https://enterprise.dji.com/matrice-350-rtk. EXCEPT
AS EXPRESSLY PROVIDED IN AFTER-SALES SERVICE POLICIES AVAILABLE AT HTTPS://WWW.DJI.
COM/SERVICE/POLICY, THE PRODUCT AND ALL MATERIALS AND CONTENT AVAILABLE THROUGH
THE PRODUCT ARE PROVIDED "AS IS" AND ON "AS AVAILABLE BASIS" WITHOUT WARRANTY OR
CONDITION OF ANY KIND.
Warnings
1. Keep liquids away from the inside of the battery station.
2. DO NOT close the cover of the battery station when charging. Make sure it is well ventilated
and able to dissipate heat.
3. The battery station is only compatible with the TB65 Intelligent Flight Battery and WB37
Intelligent Battery. DO NOT attempt to use the battery station with other battery models.
4. Place the battery station on a flat and stable surface when in use. Make sure the device is
properly insulated to prevent fire hazards.
5. DO NOT attempt to touch the metal terminals on the battery ports. Clean the metal
terminals with a clean, dry cloth if there is any noticeable buildup when powered off.
6. Take care to avoid injuring your fingers when opening or closing the battery station.
Introduction
The BS65 Intelligent Battery Station features eight TB65 battery ports, four WB37 battery ports,
a USB-C maintenance port, a USB-C charging port and a USB-A charging port. It can charge two
TB65 batteries and one WB37 battery simultaneously.
Using the Battery Station
1. Connect the battery station to a power outlet using a AC power cable.
2. Press the power button once to power on the battery station.
3. Charging the TB65 batteries:
a. Align the orange marks on the TB65 battery and the battery port, then insert the
batteries into the battery ports.
b. Toggle the charging mode switch to Storage Mode, Ready-to-Fly Mode, or Standard
Mode.
Storage Mode
after charging. Storage Mode is good for long-term battery storage.
Ready-to-Fly Mode
90% after charging. Ready-to-Fly Mode facilitates quick use of batteries.
Standard Mode
c. The battery station will charge the batteries in pairs. The pair with the highest power
will be charged first.
4. Charging the WB37 batteries: Insert the WB37 batteries, and the battery with the highest
battery level will be charged first.
5. Charging the DJI RC Plus remote controller: Connect the remote controller to the USB-C
charging port using a USB-C to USB-C cable.
The battery station should stay powered on to maintain the battery level in Storage
Mode and Ready-to-Fly Mode. Maintaining a high power level in Ready-to-Fly Mode
will affect battery life. Power off the battery station after charging, except for special
situations such as fire emergencies.
Connect the remote controller to the maintenance port and run DJI Pilot 2 to view
battery information, update the firmware, or diagnose the error.
When the temperature of the TB65 battery is below 18° C (64.4° F), the batteries will be
automatically warmed up after being inserted into battery station and powered on.
Paired Charging of Batteries
TB65 batteries should be used in pairs to extend battery life. Inserted batteries in the top
and bottom ports will be automatically paired in the sequence of A, B, C, and D. The charging
sequence is illustrated below:
Between paired and a single battery, paired batteries will be charged first.
When there are multiple battery pairs, the pair with the highest power will be charged first.
(Figure B-2)
When none of the batteries are paired, the two batteries with the highest battery level will
be charged first.
When the power of the batteries in one pair is not the same, the battery station will charge the
one with less power first, and then charge the paired batteries together once their power is
the same.
LEDs and Buzzer Description
LED Indicators
Power Button
Solid green
Battery LEDs
Blinks green
Solid green
Blinks yellow
Solid yellow
Blinks red
Solid red & buzzer beeps
Battery Station LED
Blinks yellow
Solid red & buzzer beeps
* Connect the remote controller to the maintenance port, run DJI Pilot 2, and tap HMS to
diagnose the error.
Specifications
Product model
Dimensions
Net Weight
Max Internal Load
Compatible Battery Model
Input
Output
Output Power
USB-C Charging Port
USB-A Charging Port
Output Power (when warming
up the TB65 battery)
No-load Power Consumption
Operating Temperature
Charging Time*
* Charging times are tested in a lab environment at room temperature. The values provided
should be used for reference only.
: Each battery pair is charged to 50% in sequence and kept at 50%
: Each battery pair is charged to 90% in sequence and kept at
: Each battery pair is charged to 100% in sequence.
(Figure B-3)
Description
Powered on
Charging
Charging completed
Warming up/Cooling down
Waiting to charge
Battery port communication error. Reinsert the battery or try
another battery port.
Battery error*
Updating battery station firmware
Battery station error*
BS65
580×358×254 mm
8.98 kg
12 kg
TB65 Intelligent Flight Battery
WB37 Intelligent Battery
100-120 VAC, 50-60 Hz
220-240 VAC, 50-60 Hz
TB65 Battery Port: 52.8 V, 7 A×2 @100-120 V,
8.9 A×2 @220-240 V (supports up to two outputs simultaneously)
WB37 Battery Port: 8.7 V, 6 A
100-120 VAC, 750 W
220-240 VAC, 992 W
Max. output power of 65 W
Max. output power of 10 W (5 V, 2 A)
52.8 V, 2 A
< 8 W
-20° to 40° C (-4° to 104° F)
Two TB65 batteries charged from 0% to 100%
100-120 V, 70 minutes
220-240 V, 60 minutes
(Figure A)
(Figure B)
(Figure B-1)
3
Publicidad
