Publicidad
GB
COMPONENTS AND CONTROLS (PIC .1)
VARIABLE SPEED CONTROL (PIC.2)
1
Battery
2
Battery release catch
3
On/Off trigger switch
4
Forward/reverse
5
Torque adjuster
6
Hand grip
7
Keyless chuck
8
Charger
9
Drill C/W battery
Simply apply light pressure to the trigger to start the drill on a
slow speed. Increasing the pressure will allow a variable speed
increase.
Always remove the battery before carrying out any adjustments
or maintenance.
KEYLESS CHUCK OPERATION (PIC.3)
The keyless chuck fitted to this drill/driver allows for the easy
installation and removal of bits and drills (Pic.3).
The chuck has two rotating grips (A and B). Select the drill/driver
bit required and insert it into the chuck jaws, turn grip A in a
clockwise direction until jaws grip the drill/driver bit. With your
free hand hold grip B firmly and rotate grip A in a clockwise
direction until it tightens onto the drill/driver bit. Do not use
unnecessary force to tighten.
Re-fit the battery, your drill/driver is now ready for use.
TORQUE ADJUSTMENTS (PIC.4)
This feature allows setting of the torque or tightening power
of your drill/driver and depending on the application, various
levels of driving power are required. When driving larger screw
diameters a higher torque power is required to drive the screw
until it's properly seated.
When the selected torque is reached the chuck will stop
rotating.
TECHNICAL SPECIFICATION
Voltage
Variable speed
Torque settings
Chuck size
Charger input voltage
Charger output voltage
Charge time
Drill capacity
Wood
Metal
Sound Pressure Level
Sound Power Leve
Vibration Level
All manuals and user guides at all-guides.com
NCD12
NCD144-2
12 V
14,4 V
0 - 550 min
0 - 550 min
-1
20 + 1 No.
20 + 1 No.
10 mm
10 mm
230 V ~ 50 Hz
230 V ~ 50 Hz
15 V - 400 mA
18 V - 400 mA
3-5 hr
3-5 hr
20 mm
20 mm
8 mm
8 mm
L PA 80.0 dB(A) L PA 80.0 dB(A) L PA 80.0 dB(A) L PA 80.0 dB(A)
L WA 91.0 dB(A) L WA 91.0 dB(A) L WA 91.0 dB(A) L WA 91.0 dB(A)
4.17 m/s
4.17 m/s
2
THERE ARE 16 TORQUE SETTINGS:
1-3
For driving small screws.
4-5
For driving screws into soft materials or plastics
6-7
For driving screws into soft woods.
8-9
For driving screws into medium/hard woods.
10-13
For driving screws into hard woods.
14-16
For powerful screw driving or drilling metal or using
spade (hole) bits.
NOTE: Always start on the lowest setting.
The symbol
gives the highest torque setting and is used
when drilling and for driving larger screws.
FORWARD & REVERSE SWITCH (PIC.5)
This feature is selected via a slide switch located above the
trigger. To select direction of the drill rotation simply push the
button fully in on the left side for reverse rotation.To change to
forward rotation, push the button fully in on the right side of the
handle.
WARNING!
The machine is designed as a drill and driver. Do not attach any
other accessories other than those recommended.
PLEASE NOTE
As a safety precaution from accidental engagement while being
carried pushing the forward/reverse button into the middle or
neutral position will render the drill inoperative.
HINTS FOR SCREW DRIVING
1. Use candle or bees wax on the screw threads to speed
application.
2. Whenever possible drill small diameter pilot holes for faster
screwing, eliminating the possibility of splitting the wood.
NCD144
14,4 V
0 - 550 min
-1
-1
15 + 1 No.
10 mm
230 V ~ 50 Hz
18 V - 400 mA
3-5 hr
20 mm
8 mm
4.17 m/s
2
2
16
NCHD18-2
18 V
0-400 / 0-1150 min
-1
20 + 1 No.
10 mm
230 V ~ 50 Hz
23 V - 400 mA
3-5 hr
20 mm
8 mm
4.17 m/s
2
Publicidad
