Publicidad
Idiomas disponibles
Idiomas disponibles
English
Electronic Protection System
Li‑Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading,
overheating or deep discharge. The tool will automatically
turn off and the battery pack will need to be recharged.
Important Charging Notes
1. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING:
charger from the AC outlet before cleaning. Dirt and
grease may be removed from the exterior of the charger
using a cloth or soft non‑metallic brush. Do not use
water or any cleaning solutions.
Wall Mounting
Some CRAFTSMAN chargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
nOTE: Do not attempt to mount CMCB101 charger under a
bench or table.
nOTE: Only mount CMCB101 charger with the charging
lights pointed upward toward the ceiling.
VersaTrack™
WARNING:
charger is hung on Trackwall.
CRAFTSMAN chargers, except the CMCB101, can be
stored on CRAFTSMAN VersaTrack™ Trackwall. Hooks and
accessories are sold separately. Please refer to the VersaTrack™
Trackwall accessory sheet for further information.
10
Shock hazard. Disconnect the
Do not charge batteries while
nOTE: The CMCB101 charger is not CRAFTSMAN VersaTrack™
Trackwall compatible.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING:
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories,
when replacing line, or prior to cleaning. An
accidental start‑up can cause injury.
Attaching Spool Assembly (Fig. E)
1. Install spindle plate
19
double D shaped retaining nut on the spindle sits inside
the base of the spindle plate.
2. Rotate the spindle plate until the hole
notch
22
in the housing. Insert the included rod
through the notch and into the hole, to prevent the
spindle from turning.
3. While holding the rod in place, thread the new spool
housing
10
with spool grip cover counterclockwise.
Securely tighten the new spool housing onto the spindle.
Installing the Guard (Fig. F, G)
WARNING:
Damage or personal injury could result.
WARNING:
WITHOUT GUARD FIRMLY IN PLACE. The guard
must always be properly attached on the appliance to
protect the user.
1. Assemble the guard
9
2. Using a crosshead screwdriver, insert the two guard
screws
15
and tighten securely.
nOTE: An extended coverage guard is available (sold
separately) for extra coverage if desired. Use CRAFTSMAN
replacement guard Part Number N636336.
Attaching the Auxiliary Handle (Fig. H)
1. Place the auxiliary handle
trimmer pole
6
as shown in Fig. H.
2. Slide the bracket
26
bottom of the handle.
3. Thread the handle bolts
the bracket from above.
4. Tighten the handle bolts. Ensure the handle is securely
attached by closing the handle clamp
5. To adjust the position of the auxiliary handle, open the
handle clamp and slide the handle up and down the pole
until it is in the desired location. Close the clamp to lock
the handle in place.
To reduce the risk of serious
onto the spindle
20
, so the
21
aligns with
Never remove the guard.
NEVER OPERATE appliance
to the motor housing
5
4
onto the top of the upper
of the auxiliary handle onto the
27
through the handle and into
25
.
.
Publicidad
