Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
CEILING FAN
LIGHT KITS
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRICAL
SHOCK, OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
1.
Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer at the address or telephone number
listed in the warranty.
2. Before servicing or cleaning unit, or installing a
light kit, switch power off at service panel and lock
service panel to prevent power from being switched
on accidentally. When the service disconnecting
means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the
service panel.
3. Installation work and electrical wiring must be done
by a qualified person(s) in accordance with all
applicable codes and standards, including fire-rated
construction codes and standards.
4. Make sure all wire connections are secure, and that
there are no exposed conductor strands.
5. Do not use water or detergents when cleaning the
light kit. A dry dust cloth or lightly dampened cloth
will be suitable for most cleaning.
The weight of your light kit is 13.7 lbs.
MODELS TF40BS • TF40RB • TF40WH
Glass Shades
sold separately.
INSTALLATION
CAUTION: To reduce the risk of fire and electric shock, this light kit should be
used only with these fan models manufactured by Broan-NuTone LLC: CFS52WH,
CFS52PB, CFS52BS, CFS52RB, CFH52WH, CFH52PB, CFH52BS, CFH52RB.
NOTE: Before starting installation, disconnect the power by turning off the circuit
breaker or removing the fuse at fuse box. Turning power off using the fan switch
is not sufficient to prevent electric shock.
1.
Raise and hold the light kit close to the switch housing to make wire connections.
Connect the blue wire from the switch housing to the black wire from the light kit
and connect the white wires together. Use the wire nuts supplied with the fan.
2. Attach the light kit to the threaded rod using the finial.
3. Attach fob to pull chain.
4. Mount the glass shades (purchase separately) to the light fixture by partially
unscrewing the thumb screws on the glass holder, insert the glass, then gently
tighten the thumb screws, by hand, evenly to the glass. DO NOT OVER TIGHTEN.
5. For greatest energy efficiency, install (4) 13 Watt compact fluorescent bulbs
(included).
6. Restore power and check light kit operation.
PLASTIC
PLUG
LIGHT KIT
WIRE NUTS
LIGHT KIT
ASSEMBLY
NUT
LOCK WASHER
SWITCH
HOUSING
COVER
SWITCH HOUSING
SCREWS
THUMB
SCREWS
GLASS SHADES
BULBS
Page 1
Publicidad
Manuales relacionados para NuTone TF40BS
Resumen de contenidos para NuTone TF40BS
- Página 1 CAUTION: To reduce the risk of fire and electric shock, this light kit should be SHOCK, OR INJURY TO PERSONS, OBSERVE THE used only with these fan models manufactured by Broan-NuTone LLC: CFS52WH, FOLLOWING: CFS52PB, CFS52BS, CFS52RB, CFH52WH, CFH52PB, CFH52BS, CFH52RB.
- Página 2 REMEDY: During the applicable limited warranty period, NuTone will, at its option, provide replacement parts for, or repair or replace, without charge, any fan or part, to the extent NuTone finds it to be covered by and in breach of this limited warranty. NuTone will ship the repaired or replaced fan or replacement parts to you at no charge.
- Página 3 ELÉCTRICA O LESIONES, SIGA LAS INDICACIONES iluminación sólo debe ser utilizado con los siguientes modelos de ventiladores QUE SE ENUMERAN A CONTINUACIÓN: fabricados por Broan-NuTone LLC: CFS52WH, CFS52PB, CFS52BS, CFS52RB, CFH52WH, CFH52PB, CFH52BS, CFH52RB. Utilice esta unidad sólo de la forma indicada por el fabricante.
- Página 4 CÓMO OBTENER EL SERVICIO CUBIERTO POR LA GARANTÍA: Para tener derecho al servicio cubierto por la garantía, usted debe (a) notificar a NuTone a la dirección o número de teléfono que aparecen abajo en un plazo de siete (7) días después de descubrir el defecto cubierto, (b) proporcionar el número de modelo y la identificación de la pieza y (c) describir la naturaleza de cualquier defecto en el ventilador...