Metabo 602395840 Manual Original página 10

en ENGLISH
Observe the relevant guidelines and national
regulations for your material, staff, application and
place of application (e.g. occupational health and
safety regulations, disposal).
Collect the particles generated at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits,
- use an extraction unit and/or air purifiers,
- ensure good ventilation of the workplace and keep
clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash the protective clothing. Do not
blow, beat or brush.
5. Overview
See page 2.
1 Square attachment for 1/2" tools*
2 Hexagon socket attachment for hexagon
screwdriving bits*
3 Locking sleeve*
4 Rotation selector switch / Transporting safety
device
5 Trigger
6 Handle (gripping surface)
7 LED light
For working on dimly lit areas. The LED lights
light up when the machine is switched on.
8 Setting wheel for preselecting rotational speed
and tightening torque
9 Battery pack *
10 Battery pack release button
11 Capacity indicator button *
12 Capacity and signal indicator *
13 Belt hook (attach as shown) *
* depending on the features / model
6. Initial Operation/Setting
Remove the battery pack from the machine
before any adjustment or maintenance is
carried out. Before fitting the battery pack, make
sure that the machine is switched off.
6.1 Battery pack
Charge the battery pack before use (9).
If performance diminishes, recharge the battery
pack.
Instructions on charging the battery pack can be
found in the operating instructions of the Metabo
charger.
10
"Li-Power, LiHD" li-ion battery packs have a
capacity and signal indicator: (12)
- Press the button (11), the LEDs indicate the
charge level.
- If one LED is flashing, the battery pack is almost
flat and must be recharged.
Removal:
Press the battery pack release (10) button and pull
the battery pack (9) forwards.
Inserting:
Slide in the battery pack (9) until it engages.
6.2 Setting the direction of rotation, engag-
ing the transporting safety device
(switch-on lock)
Do not actuate the rotation selector switch or
engage the transportation lock (4) unless the
motor has stopped completely!
Actuate the rotation selector switch / Engage the
transportation lock (4)
R = Right rotation set
(insert screws)
L = Left rotation set
(remove screws)
0 = Central position: transportation lock setting
(switch-on lock)
6.3 Switching on and off
Switching on: press the trigger switch (5).
Switching off: release the trigger switch (5).
6.4 Speed / tightening torque
The speed and tightening torque are connected
directly. The lower the speed, the lower the
tightening torque.
The tightening torque is influenced in two ways:
1) Preselect operating mode/desiredtightening
torque at the setting wheel (7):
= max. tightening torque (power mode)
P
= adjustable tightening torque
. ..
= especially for self-cutting screws: at the
beginning high speed (for drilling) and later low
speed (for tightening the screw).
2) Stepless adjustment of the tightening torque:
The speed and tightening torque can be adjusted
steplessly in any position of the setting wheel by
pressing the trigger (5) firmly or lightly, thus
adapting to working conditions.
Recommendation: determine the correct setting
by carrying out trial screwdriving.
6.5 Changing screwdriving bit for SSD...
Inserting screwdriving bit: Slide locking sleeve
(3) forward and insert screwdriving bit as far as the
stop. Release locking sleeve (3).
Pull on the screwdriver bit to check that it is
correctly seated.
Removing screwdriving bit: Slide locking sleeve
(3) forward and remove screwdriving bit.