Publicidad
Idiomas disponibles
Idiomas disponibles
Thank You
Thank you for purchasing this product. It was carefully engineered to provide excellent performance
when properly operated and maintained.
Please read this entire manual prior to operating the equipment. It instructs you how to safely and
easily set up, operate and maintain your machine. Please be sure that you, and any other persons who
will operate the machine, carefully follow the recommended safety practices at all times. Failure to do
so could result in personal injury or property damage.
All information in this manual is relative to the most recent product information available at the time.
Review this manual frequently to familiarize yourself with the machine, its features and operation.
Please be aware that this Operator's Manual may cover a range of product specifications for various
models. Characteristics and features discussed and/or illustrated in this manual may not be applicable
to all models. We reserve the right to change product specifications, designs and equipment without
notice and without incurring obligation.
Contents of Carton
•
Chipper Shredder
•
Operator's Manual
•
Engine Operator's Manual
•
Bottle of Oil
•
Tow Bar (If Equipped)
•
Bag
•
Safety Glasses
Assembly
NOTE: This unit is shipped without gasoline or oil in
the engine. Fill up gasoline and oil as instructed in the
accompanying engine manual BEFORE operating your
chipper shredder.
Chipper Chute (Model Series CS3310 & 4325)
For shipping reasons, the unit is crated with its chipper
chute in a raised position. To pivot it downward,
proceed as follows:
1.
Pull the spring latch upward. See A in Figure 1.
2.
Gently pivot the chipper chute down until it
clicks into the lock rod. See B in Figure 1.
Never operate the chipper shredder with the chipper chute in the raised
position. Doing so may result in property damage or serious injury to the
operator or bystanders.
Bag
To attach the bag:
1.
Place the opening of the bag completely
over the chute deflector. See Figure 2.
2.
Position the bag so the wing knobs
which secure the chute deflector to the
impeller housing are completely covered.
3.
Pull on the draw-strap until the bag is
tight around chute deflector opening.
ASSEMBLY & INSTALLATION
Figure 1
WARNING
Figure 2
If applicable, the power testing information used to establish the power rating of the engine equipped
on this machine can be found at www.opei.org or the engine manufacturer's web site.
If you have any problems or questions concerning the machine, phone your local authorized service
dealer or contact us directly. We want to ensure your complete satisfaction at all times.
Throughout this manual, all references to
operating position.
Tow Bar (If Equipped)
To attach the tow bar:
1.
Remove the spring pin and clevis pin
from the end of the tow bar receiver.
See Figure 3.
2.
Insert the tow bar into the receiver. See
Figure 4.
3.
Reinsert the clevis pin through aligning
holes in both the tow bar and the
receiver. See Figure 4.
4.
Fasten with the spring pin to secure. See
Figure 4.
Set-Up
A
Gas and Oil Fill-Up
Refer to the separate engine owner's manual
B
for additional engine information.
1.
Add oil provided before starting unit
for the first time out of the box. See the
separate Engine Operator's Manual for
instructions for adding the engine oil.
2.
Service the engine with gasoline as
instructed in the separate Engine
Operator's Manual.
Use extreme care when handling gasoline. Gasoline is extremely
flammable and the vapors are explosive. Never fuel the machine indoors or
while the engine is hot or running. Extinguish cigarettes, cigars, pipes and
other sources of ignition.
Never fill fuel tank indoors with engine running or until the engine has
been allowed to cool for at least five (5) minutes after running.
4
right
left
and
side of the machine are observed from the
1
Figure 3
2
Figure 4
WARNING
WARNING
4
3
Publicidad
