DeWalt DXST4500WTD Manual De Instrucciones

JS PRODUCTS | 6445 MONTESSOURI STREET, LAS VEGAS, NV 89113
(APR18) Part No. 41567
Copyright © 2018 D
D WALT and the D WALT Logo are trademarks of the D
®
E E
and are used under license. The yellow/black color scheme is a trademark for D
Definitions: Safety Guidelines
The definitions below describe the level of severity for each signal word. Please
read the manual and pay attention to these symbols.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
(Used without word) Indicates a safety related message.
NOTICE: Indicates a practice not related to personal injury which, if not avoided,
may result in property damage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D
CALL US TOLL FREE AT: 1-844-377-8451
WARNING! Read and understand all instructions.
manual contains important safety and operating instructions.
Please read this manual carefully before assembling this storage
rack and save it for reference.
SAVE THESE INSTRUCTIONS
TECHNICAL SPECIFICATIONS
Technical Specifications
Total Capacity for Worktop Surface
Drawer Capacity
Worktop Drawer Exterior Dimensions
Drawer Interior Dimensions
GENERAL SAFETY
• Keep work area clean and dry.
• Use correct/recommended tools for the job.
• Never leave tools unattended.
• Never force a part into place.
• Wear safety apparel.
• Wear safety glasses/goggles.
• Never crawl, sit, stand, or climb on the Worktop Drawer.
• Never crawl, sit, stand, or climb on the rack.
• Never overload the Worktop Drawer.
• Do not leave drawer open.
• Keep small parts away from children. Never leave small children unattended while assembling.
• Always use common sense – your personal safety is your responsibility.
DXST4500WTD Copyright © 2018, D
E
WALT.
E
WALT Industrial Tool Co., or an affiliate thereof
E
WALT power tools
E
& accessories.
WALT TOOL,
E
1000 lb (453.59 kg)
*when weight is evenly distributed
120 lb (54.43 kg)
*when weight is evenly distributed
Width: 44.13" (112.09 cm)
Height: 8.27" (21.01 cm)
Depth: 19.12" (48.56 cm)
Width: 41.02" (104.19 cm)
Height: 5.47" (13.89 cm)
Depth: 18.43" (46.81 cm)
SPECIFIC SAFETY FOR WALL MOUNT BRACKET
WARNING:
be secured to the wall, especially in earthquake-prone areas, or where surfaces are uneven, and where children
and/or pets are present. For added safety we recommend also mounting the rack to the floor using D
number DXSTA04MP (sold separately).
WARNING:
FOR THIS WORKTOP DRAWER
• Maximum load for worktop surface is 1000 lbs (453.59 kg) when weight is evenly distributed.
• Maximum load of the drawer is 120 lbs (54.43 kg) when weight is evenly distributed.
Parts List
No. Description
1 Pre-Assembled Drawer
2 Drawer Pull
3 Left Mounting Bracket
4 Right Mounting Bracket
5 Mounting Bracket Bolt
6 Locking Pin
7 Push Pin
8 4 mm Hex Key
9 4 mm Hex Bit
1
2
3
WALT
4
5
Worktop Drawer Configurations
NOTE: The Worktop Drawer can be mounted at different levels on the DXST4500 Industrial Rack series for
multi-functional organization.
NOTE: See images below for different Worktop Drawer mounting options.
This
*Shelf Replacement Setup
NOTE: DXST4500 Industrial Racks and DXST4500PBK Pegboards are sold separately.
BEFORE YOU BEGIN:
• Read all instructions thoroughly.
• Remove all components from the box, and lay them on the floor in an orderly fashion.
• Wear eye protection.
• Be cautious of sharp edges.
• Keep this information for further reference.
Serious injury or death can occur from the rack tipping over. To prevent this, the rack must
NEVER EXCEED THE FOLLOWING WEIGHT LIMITS
Qty.
1
1
2
2
8
4
2
1
1
6
7
8
9
*Workbench Setup with 2-DXST4500, 1-DXST4500PBK, and
1-DXST4500WTD
READ ALL INSTRUCTIONS
WALT part
E