Care And Maintenance - EDM 08756 Manual De Instrucciones

Cordless Vacuum
Operating Instructions
Before use
Remove any packing material and loose parts from unit.
Check the accessories before use. It should be fit with the
machine and your purpose. If the machine is new, the
battery must first be charged.
Attention! After long time storage, the battery capacity will
be reduce.
A new battery or one which has not been used for an
extended period achieves full performance only after
charging and discharging cycles. A substantial drop in
operating period per charge indicates that the battery is
worn out and must be replaced.
Battery charger (Fig.2)
The lithium-ion battery can be charged at any time and will
not develop a "memory" when charged after only a partial
discharge. It is not necessary to run down the battery pack
charge before recharging. Remove the battery pack from the
tool when convenient for you and your job. You can "top-off"
your battery pack's charge before starting a big job or long
period of use.
Due to lithium-ion's fade-free properties, the only time it is
necessary to charge the lithium-ion battery pack is when the
pack has reached the end of its charge. To signal the end of
charge, power to the tool will drop quickly. Charge the
battery pack as needed.
1. Charging the battery
This lithium-ion battery pack is shipped partially charged.
Before using it the first time, fully charge the battery pack. A
fully discharged battery pack with a temperature between
5°C and 40°Cwill charge in about 1 hour for 2.0Ah battery
pack.
· Plug the charger adapter into power source. The green light
on the charger stand will illuminate, indicating the charger is
powered.
· Slide the battery all the way into the charger stand. The
green light is off, and the red light on the charger stand will
illuminate, indicating that the battery is charging.
· The red light will go off after charging is complete and a
green light will appear
.
NOTE: Batteries may become warm while charging. This is
normal. If the battery is hot after continuous use in the tool,
allow it to cool down to room temperature before charging.
This will extend the life of your batteries.
WARNING: Always disconnect the battery pack from the tool
before any assembly, adjustments or changing accessories.
2. Insertion and removal of rechargeable battery (Fig.3)
Depress the battery-release button located on the front of
the battery pack to release battery pack. Pull the battery
pack out and remove it from the tool.
Warning!
Always remove the battery pack before making adjustments
to the equipment.
INSTRUCTION MANUAL
EN
Be sure to read the following information before you put the
cordless equipment into operation: Charge the battery pack
with the charger. An empty battery pack requires a charging
period of approximately 0.5 to 1 hour for 2.0Ah battery pack.
Mounting VAC Accessories
Remove the battery pack from the vacuum cleaner before
maintaining or cleaning, making any adjustments, changing
accessories or placing the vacuum cleaner aside. This safety
measure prevents accidental starting of the vacuum cleaner.
The vacuum cleaner accessories can be connected directly
to the dust cup.
The combination possibilities of the various vacuum cleaner
accessories can be viewed in the figure. Connect the vacuum
cleaner accessories firmly to the connection at the dust cup
and in to each other.
Switch on and off
Before vacuuming, ensure that the filter assembly is
assembled securely.
To save energy, only switch the vacuum cleaner on when
using it.
• To switch on the vacuum cleaner, move the On/Off switch
forwards (direction ON).
• To switch off the vaccum cleaner, move the On/Off switch
backwards (direction OFF).
Cleaning the dust cup
To maintain the optimum performance of the vacuum
cleaner, clean the dust cup after each use.
• Press release button and remove the dust cup from the
motor housing.
• Shake/tap out the dust cup over a suitable waste bin. If
required, clean the dust cup with a moist cloth. • Afterwards,
hang the dust cup at the bottom into the motor housing,
apply light pressure until the dust cup can be heard to
engage.

Care and Maintenance

Keep the ventilation openings clear and clean the product
regularly. This machine requires no special mechanical
maintenance such as greasing the bearings.
If something unusual occurs during use, switch off the
supply and remove the battery pack. Inspect and repair the
tool before using it again. The repairs must be carried out by
a qualified technician.
Repair of the tool must only be carried out by a qualified
repair technician.
Repair or maintenance by unqualified personnel can lead to
a risk of injury.
Use only identical spare parts for repairing a tool.
Caution! If there's any defective found of the battery pack, it
must be repaired or replaced by the
assigned service organization.
REF. 08756