Publicidad
Idiomas disponibles
Idiomas disponibles
TROUBLESHOOTING TIPS
Problem
Start status indicator
light flashing
Dishwasher BEEPS
once every minute
Beeping at the end of
the cycle
Dishes and flatware
not clean
Spots and filming on
glasses and flatware
Cloudiness on
glassware
Suds in the tub
20
Possible Cause
The door was opened or the
cycle was interrupted.
This is a reminder that your
dishwasher door has been left
open during operation. It will
continue beeping until you
press Start and close the door.
This is normal. Dishwasher
will beep at end of cycle.
Filter assembly is clogged
Low inlet water temperature
Water pressure is temporarily
low
Air gap or disposer clogged
High drain loop or air gap not
installed
Improper rack loading
Poor performing detergent
Extremely hard water
Low inlet water temperature
Overloading or improper
loading of the dishwasher
Old or damp powder
detergent
Rinse agent dispenser empty
Too little or low performing
detergent
Combination of soft water
and too much detergent
Low performing phosphate-
free detergent
Water temperature entering
dishwasher exceeds 150°F (66°C)
Wrong detergent
Rinse agent was spilled
What To Do
Press the Start pad once and close the door within 4 seconds to
start the dishwasher. Press the Start pad a second time when
the dishwasher is running only if you wish to cancel the cycle.
Press Start and close the door.
To turn off the double beep indicator (or re-activate it if it was
previously turned off), press the Dry pad 5 times within 3
seconds. A triple beep will sound to indicate the end-of-cycle
beep option has been turned on or off.
See the CARE AND CLEANING section.
Make sure inlet water temperature is correct (see the USING
THE DISHWASHER section). Turn on the hot water faucet
nearest the dishwasher, let run until the water temperature stops
rising. Then start the dishwasher and turn off the faucet. This
ensures the entering water is hot. Select Temp.
Turn on a faucet. Is water coming out more slowly than usual? If so,
wait until pressure is normal before using your dishwasher. Normal
water pressure to the dishwasher should be 20-120 psi.
Clean the air gap or flush the disposer.
Refer to the Installation Instructions for proper drain line
installation.
Make sure large dishware or utensils do not block the detergent
dispenser or the wash arms. See the LOADING section.
Use high quality detergents such as
or
Finish
Quantum®
Automatic Dishwashing
®
Use high quality rinse agents such as Cascade® Platinum™
Power Dry™ Rinse Aid or Finish® Jet-Dry®
spots and prevent new film build-up.
If water is extremely hard, a softener may be required.
Make sure inlet water temperature is at least 120°F (49°C).
Load dishwasher as shown in the LOADING section.
Make sure detergent is fresh.
as
Cascade
Platinum™ ActionPacs™ or Finish®
®
Automatic Dishwashing
Detergent.
Refill with high quality rinse agents such as Cascade® Platinum™
Power Dry™ Rinse Aid or Finish® Jet-Dry® Rinse Aid.
Make sure you use the proper amount of highly rated
detergent.
This is called etching and is permanent. To prevent this from
happening, use less detergent if you have soft water. Wash
glassware in the shortest cycle that will get it clean.
See A white film on glassware, dishware and the interior in
this TROUBLESHOOTING TIPS section.
This could be etching. Lower the water heater temperature.
Use only high quality automatic dishwasher detergents to avoid
®
sudsing. Cascade
Platinum™ ActionPacs™ or
Automatic Dishwashing Detergent
Haier Appliances
dishwashers.
Always wipe up rinse agent spills immediately.
Cascade® Platinum™ ActionPacs™
Detergent.
Rinse Aid
to prevent
Use high quality detergents such
Quantum
®
Finish
Quantum
®
have been approved for use in all
®
49-4000207 Rev 2
Publicidad
