Candy CFT610/3X Montaje Y Modo De Empleo página 10

WEEE subjected to specific treatments, in order to remove
and dispose properly all pollutants, and recover and recycle all
materials.
Individuals can play an important role in ensuring that WEEE
does not become an environmental issue; it is essential to
follow some basic rules:
− WEEE should not be treated as household waste;
− WEEE should be handed over to the relevant collection
points managed by the municipality or by registered
companies. In many countries, for large WEEE, home
collection could be present.
In many countries, when you buy a new appliance, the old one
may be returned to the retailer who has to collect it free of
charge on a one-to-one basis, as long as the equipment is of
equivalent type and has the same functions as the supplied
equipment.
Appliance designed, tested and manufactured according to:
• Safety: EN/IEC 60335-1; EN/IEC 60335-2-31, EN/IEC
62233.
• Performance: EN/IEC 61591; ISO 5167-1; ISO 5167-3; ISO
5168; EN/IEC 60704-1; EN/IEC 60704-2-13; ISO 3741; EN
50564; IEC 62301.
• EMC: EN 55014-1; CISPR 14-1; EN 55014-2; CISPR 14-2;
EN/IEC 61000-3-2; EN/IEC 61000-3-3. Suggestions for a
correct use in order to reduce the environmental impact:
Switch ON the hood at minimum speed when you start
cooking and kept it running for few minutes after cooking is
finished. Increase the speed only in case of large amount of
smoke and vapour and use boost speed(s) only in extreme
situations. Replace the charcoal filter(s) when necessary to
maintain a good odour reduction efficiency. Clean the grease
filter(s) when necessary to maintain a good grease filter
efficiency. Use the maximum diameter of the ducting system
indicated in this manual to optimize efficiency and minimize
noise.
By placing the marking on this product, we declare,
on our own responsability, compliance to all of European
safety, health and environmental requirements stated in the
legislation for this product.
Installation
The minimum distance between the supporting surface for the
cooking equipment on the hob and the lowest part of the
range hood must be not less than 50cm from electric cookers
and 65cm from gas or mixed cookers.
If the instructions for installation for the gas hob specify a
greater distance, this must be adhered to.
The template (*) can be used for installation.
Electrical connection
The mains power supply must correspond to the rating
indicated on the plate situated inside the hood. If provided with
a plug connect the hood to a socket in compliance with current
regulations and positioned in an accessible area, after
installation. If it not fitted with a plug (direct mains connection)
or if the plug is not located in an accessible area, after
installation, apply a double pole switch in accordance with
standards which assures the complete disconnection of the
mains under conditions relating to over-current category III, in
accordance with installation instructions.
Warning! Before re-connecting the hood circuit to the mains
supply and checking the efficient function, always check that
the mains cable is correctly assembled.
Warning! If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly qualified
persons in order to avoid hazard.
Operation
The hood is fitted with a control panel with aspiration speed
selection control and a light switch to control cooking area
lights.
Maintenance
Cleaning
Clean using ONLY the cloth dampened with neutral liquid
detergent. DO
INSTRUMENTS. Do not use abrasive products. DO NOT USE
ALCOHOL!
Grease filter - Carbon filter (*): it is/they are mounted on the
back of the grill and must be changed once a month.
If the metal fats filter is envisaged in the model in your
possession, this must be cleaned once a month with non-
aggressive detergent manually or in a dishwasher at low
temperature and short cycle.
The metal anti-fats filter might discolour by washing in a
dishwasher but its filtering characteristics do not change at all.
Replacing lamps
Disconnect the appliance from the electricity.
Warning! Prior to touching the light bulbs ensure they are
cooled down.
Replace the old light bulb with the one of the same type as
specified in the feature label or near the light lamp on the
hood.
Replace the damaged lamp.
Use Ø35mm E14 28W halogen candle lamps only.
If the lights do not work, make sure that the lamps are fitted
properly into their housings before you call for technical
assistance.
10
NOT CLEAN WITH TOOLS OR