Publicidad
Idiomas disponibles
Idiomas disponibles
OBJ_BUCH-617-003.book Page 12 Thursday, June 9, 2016 11:03 AM
12 | English
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
External Dust Extraction (see figure A)
Attach a vacuum hose 7 onto the outlet piece 3. Connect the
vacuum hose 7 with a vacuum cleaner. An overview for con-
necting to various vacuum cleaners can be found at the begin-
ning of these operating instructions.
The vacuum cleaner must be suitable for the material being
worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use a special vacuum cleaner.
Replacing the Sanding Sheet (see figure B)
When attaching a new sanding sheet, remove any dust or de-
bris from the sanding plate 5 (e. g. with a brush).
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
The sanding plate 5 is fitted with Velcro backing for quick and
easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 4, free the Velcro backing
of the sanding plate 5 from any debris by tapping against it in
order to enable optimum adhesion.
Position the sanding sheet 4 flush alongside one edge of the
sanding plate 5, then lay the sanding sheet onto the sanding
plate and press firmly.
To remove the sanding sheet 4, grasp it at one of the tips and
pull it off from the sanding plate 5.
Sanding accessories, such as fleece pads/polishing cloth
pads, are attached to the sanding plate in the same manner.
Selecting the Sanding Sheet
Depending on the material to be worked and the required rate
of material removal, different sanding sheets are available:
For the working of all types of materi-
als such as wood, paint, filler, lacquer,
hard and soft wood as well as chip-
boards and metal.
For coarse-sanding, e. g. of rough,
unplaned beams and boards
For face sanding and planing small
irregularities
For finish and fine sanding of hard
woods
For reworking or polishing, especially of metal and stone, use
fleece/polishing cloth pad.
Depending on the desired surface quality of the workpiece,
different fleece types or polishing cloth pads are to be used.
Replacing the Sanding Plate (see figure C)
Slide the SDS button for release of the sanding plate 6 all
the way to the right.
1 609 92A 1P5 | (9.6.16)
Remove the sanding plate 5.
Guide the sanding plate 5 from below against the sand-
ing plate holder and firmly press them together.
Slide the SDS button for release of the sanding plate 6 all
the way to the left.
If, e. g., the front tip of the sanding sheet is worn, you can also
remove the complete sanding plate and reattach it turned by
120°.
Specialty Sanding Plates
You can replace the supplied sanding plate 5 with a specialty
sanding plate, which is available as an accessory.
The specialty sanding plate is attached in the same manner as
the one supplied.
Attach and remove the respective sanding sheets in the same
manner as when changing original sanding sheets.
Pad Extender (see figure D)
With the pad extender 8 you can sand surfaces that are diffi-
cult to access, such as sills on windows, cabinets or doors.
Pad Extender, Narrow (see figure E)
With the narrow pad extender 10 you can sand narrow open-
ings, slots and passages.
Pad Extender, Narrow Rounded (see figure F)
The narrow rounded pad extender 11 allows you to sand
curved and hollow areas or surfaces that are curved inward,
such as on furniture, rails or heating radiators.
Operation
Starting Operation
Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
Grain size
To start the machine, push the On/Off switch 1 towards the
front to "I".
40–180
To switch off the machine, push the On/Off switch 1 towards
the rear to "0".
To save energy, only switch the power tool on when using it.
coarse
40
Preselecting the Orbital Stroke Rate
With the thumbwheel for preselection of the orbital stroke
medium 80, 120
rate 2, you can preselect the required orbital stroke rate, even
during operation.
fine
180
The required stroke rate depends on the material and the
working conditions and can be determined through practical
testing.
Working Advice
Wait until the machine has come to a standstill before
placing it down.
Before any work on the machine itself, pull the mains
plug.
Bosch Power Tools
Publicidad
