Oster 97 Manual De Instrucciones página 5

CORDLESS OPERATION
1) Remove the appliance from the charging stand. (See section titled "HOW TO CHARGE THE UNIT" before initial
use).
2) Turn the appliance «ON» (|) using the switch located on the front of the unit and use the appliance. If the
appliance does not turn «ON» (|), then the battery may be fully depleted and may have to be partially charged
prior to re-use. Follow the charging procedure and let the battery charge for approximately 100 minutes.
3) Turn the appliance «OFF» (O) when finished using.
4) Insert appliance into charging stand or plug into the power cord.
MAINTENANCE
STORAGE
1) Store your appliance in a clean, dry space.
2) Do not wrap the cord around the appliance when storing. This can damage the cord insulation.
3) Always take care not to tangle the cord while using or storing the appliance.
4) We recommend storing the appliance and cord in the original carton when not in use.
BLADE CARE
DETACHABLE BLADE CLIPPERS
REMOVING OR REPLACING BLADES
IMPORTANT : Make sure the appliance is turned off and unplugged before removing any part.
TO REMOVE:
Cordless Turbo A5 has a locking mechanism. To remove, push in locking mechanism
below the heel of the blade to release the blade, then lift blade away from clipper and slide
off tongue.
Cordless Model 97 does not have a locking mechanism. To remove, lift the blade away
from clipper and slide off tongue.
TO REPLACE:
Turn motor «ON» (|); insert blade on tongue fully then snap blade into place.
LUBRICATING THE BLADES
Blades should be oiled regularly to reduce heat, maintain sharpness and will extend run time per battery charge
cycle by reducing friction. Before removing the blade, be sure it has cooled down and the appliance is unplugged.
Carefully slide the upper blade left or right to apply one or two drops of provided Oster
Lubricating Oil or other Oster approved lubricant on each running rail of the lower blade. Excess oiling will cause
TM
hair to stick between teeth, slowing or jamming blades. Wipe excess oil with a dry, soft cloth.
KEEP OUT OF REACH OF CHILDREN. This is not a toy. May cause long lasting harmful effects to aquatic life.
May be harmful if swallowed, in contact with skin, or if inhaled. Avoid contact with skin, eyes and clothing. Avoid
breathing dust /fume /gas /mist /vapors /spray. Avoid release to the environment. Use only outdoors or in a
well-ventilated area. IF INHALED: remove person to fresh air and keep comfortable for breathing. Call a POISON
CENTER/ doctor if you feel unwell. Dispose of contents/ container in accordance with local/regional /national /
international regulations.
Remove cap and cut end tip. Gently squeeze tube. Keep nozzle clean. Secure cap after use.
076076CL_078005CL_076076-810-050_078005210-050_21MLM2 (EMEA).indd 8-9 076076CL_078005CL_076076-810-050_078005210-050_21MLM2 (EMEA).indd 8-9
English
Clipper & Blade
TM
8
KEEP OUT OF REACH OF CHILDREN. This is not a toy. May be fatal if swallowed and enters airways. Avoid
contact with skin, eyes or clothing. Avoid ingestion and inhalation. IF SWALLOWED: immediately call a POISON
CENTER/doctor. Do NOT induce vomiting. Store locked up in a cold, dry place. Dispose of contents/ container in
accordance with local/ regional/ national/ international regulations.
BLADE SHARPENING
Oster™ cutting blades are of individual hollow-ground design, hardened to extend cutting life. As with any cutting
instrument, the cutting edges will become dull with usage. Increasing blade tension to force dull blades to cut
can cause the appliance to heat and reduce motor life, and further shorten blade life. When the cutting blades no
longer cut smooth and clean, sharpening is necessary.
When sharpening blades becomes necessary, send blades to an Oster™ Authorized Service Center where
approved methods, equipment and proper knowledge are used to restore the original hollow-ground design and
cutting ability. DO NOT sharpen blades by flat grinding or any method contrary to the design and construction of
Oster™ cutting blades.
CLEANING
BLADES
To clean the blades, fill a flat dish with Oster™ Blade Wash
DO NOT IMMERSE THE APPLIANCE. Turn «ON» (|) the appliance with the blades facing down. Do not hold the
appliance upright when cleaning blades with the appliance plugged in. Listen for a change in the hum of the
motor. As the build-up is removed, the clean blade runs faster and at a higher pitch. When the pitch stabilizes
(between 30 to 60 seconds), turn «OFF» (O) the appliance and unplug. Remove from the cleaning solution and,
while holding the appliance with the blade end facing down, wipe the blades dry with a clean, dry cloth. Re-oil
blades.
Always unplug the appliance when carrying out other cleaning and do not immerse the appliance body, charging
stand, adapter, power cord or plug in water or any other liquid.
CHARGING STATION
1. Disconnect the charging station from the power supply.
2. If necessary, remove hairs from both charging cavities.
3. If dirty, clean the contacts with a dry cloth.
CONTACTS
If required, clean the contacts of the batteries and the clipper with a dry cloth.
Any maintenance beyond the cleaning and lubricating instructions in this manual should be performed by an
Oster™ Authorized Service Center.
WARNING When using or cleaning this appliance, do not use any aerosol sprays or blade washes,
especially those containing methylene chloride, dimethyl benzyl ammonium chloride, or 1-1-1
trichloroethylene. Damage caused by these chemicals will void your warranty. You may use
Oster approved blade washes, lubricants and disinfectant sprays that do not harm the product.
TM
English
cleaning solution and immerse only the blade teeth.
®
9
2021/10/29 下午4:59 2021/10/29 下午4:59