CANGAROO VERDE DQ-X03 Instrucciones De Uso página 12

3. Pour 100 ml of water into the opening of the sterilizer base as shown in Figure AD 1.We recommend you the
use of boiled or filtered water in order to reduce the risk of limescale deposition. Do not pour more than the
recommended quantity of water in the opening to prevent water from entering the outlet and damaging the
appliance's electric heater.
4. Place the bottle and accessory stand on the base of the sterilizer so that the bottle holders face upwards, as
shown in Figure AD 2.
5. Replace the lid of the sterilizer (Figure AD 3).
6.Plug the supply cord into electric power outlet and turn on the start button. Press the mode switch button
(M) to select the disinfection or steam function.
7. Once the water has reached 100°C, it will turn into steam. When the water evaporates completely, the
sterilizer will automatically turn off.
8.Leave the sterilizer to cool down for about 3 minutes. Turn off the power switch and unplug the supply cord.
9.Take off the upper lid, the tray and the main body of the sterilizer and pour out the residual water. Wipe and
dry. Now the sterilizer is ready for use!
➢WARNING! If you do not clean the sterilizer's base from scale deposition every week, as described in section
"GUIDELINES FOR MAINTANCE AND CLEANING OF THE STERILIZER", the product will not function normally! We
recommend you to use pre-boiled or filtered water in the device in order to reduce the risk of lime scale
deposition.
➢This sterilizer can fit up to 6 bottles with standard neck of any brand, as well as other baby feeding supplies,
such as feeding bowls, cups and spoons.
➢The product can also be used for sterilizing accessories, which come into contact with milk – such as breast
pump.
➢Note: Before sterilizing baby bottles and other accessories, first you must clean them with water and soft
detergent!
➢Note: If you want to use the sterilizer again, you should wait about 1 hour after the first use.
➢WARNING! Never open the lid during sterilization. If the process is being interrupted, the items will not be
sterilized.
➢Never use the sterilizer without water.
II. METHODS OF USE (FUNCTIONS)
A. STERILISATION WITH DRYING: FIGURE 1
1.Pour 100ml of water into the reservoir in the base of the unit. Do not add more than 100ml.
2. Place the bottle and accessory stand on the base of the sterilizer so that the bottle holders face upwards, as
shown in Figure AD 2.
3. Arrange the items you wish to sterilize as follows: teats and pacifiers on the small accessory holder and
bottles on the bottle holders. If you need to sterilize larger items, such as feeding bowls and plates, you can
remove the bottle holders.
4.Plug the supply cord to the power outlet and turn on the switch.
5.Press the start button. Then press the mode switch button (M) to select disinfection with drying mode
(disinfection + drying). After 3 flashes the mode is activated. Sterilization takes from 6 to 8 minutes, drying
process about 60 minutes. The remaining minutes will count down on the display. Using "+" button you can
increase drying time to 90 minutes.
6.Once the sterilization cycle is complete, drying mode is automatically activated.
7.Leave the sterilizer to cool down for about 3 minutes. Turn off the power switch and unplug the supply cord.
9.Take off the lid and leave the unit until the steam spreads out. After that take out the sterilized objects.
➢Be careful – the sterilized items may still be hot.
9.Take off all of the compartments of the appliance and pour out the residual water. Wipe dry the sterilizer.
B. STERILISATION: FIGURE 2
1.Pour 100ml of water into the reservoir in the base of the unit.Do not add more than 100ml.
2. Place the bottle and accessory stand on the base of the sterilizer so that the bottle holders face upwards, as
shown in Figure AD 2.
3. Arrange the items you wish to sterilize as follows: teats and pacifiers on the small accessory holder and
bottles on the bottle holders. If you need to sterilize larger items, such as feeding bowls and plates,
11