Bosch Professional GWS 12-125 S Manual Original página 20

20 | English
wires by applying excessive load to the brush The wire
bristles can easily penetrate light clothing and/or skin.
If the use of a guard is recommended for wire brush-
u
ing, do not allow any interference of the wire wheel or
brush with the guard. Wire wheel or brush may expand
in diameter due to work load and centrifugal forces.
Additional safety information
Wear safety goggles.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Release the On/Off switch and set it to the off position
u
when the power supply is interrupted, e. g., in case of
a power failure or when the mains plug is pulled. This
prevents uncontrolled restarting.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for cutting, roughing and brush-
ing metal and stone materials, as well as making holes in
stone materials using diamond core cutters, without the use
of water.
A separate protective guard for cutting must be used when
cutting with bonded abrasives.
1 609 92A 7ZN | (23.06.2022)
Sufficient dust extraction must be provided when cutting
stone.
With approved abrasive tools, the power tool can be used for
sanding with sanding discs.
The power tool must not be used to grind concrete.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Unlocking lever for protective guard
(2) Spindle lock button
(3) On/off switch
(4) Speed preselection thumbwheel
(5) Auxiliary handle (insulated gripping surface)
(6) Protective guard for cutting
(7) Protective guard for grinding
(8) Extraction guard for grinding
(9) Mounting flange with O‑ring
a)
(10) Carbide grinding head
a)
(11) Grinding disc
a)
(12) Cutting disc
(13) Quick-clamping nut
(14) Clamping nut
(15) Quick-clamping nut with bar
(16) Two-pin spanner for clamping nut
(17) Grinding spindle
(18) Handle (insulated gripping surface)
(19) Extraction guard for cutting with cutting guides
a)
(20) Diamond cutting disc
a)
(21) Hand guard
a)
(22) Cup brush
a)
(23) Rubber sanding pad
a)
(24) Abrasive disc
a)
(25) Round nut
a)
(26) Diamond annular cutter
a)
(27) Open-ended spanner
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Angle Grinder
Article number
Rated power input
Power output
Rated speed
Speed adjustment range
Max. grinding disc diameter
a)
a)
a)
a)
a)
GWS 12-125 S
3 601 CA6 0..
W 1200
W 630
–1
min 11,000
–1
min 2800–11,000
mm 125
Bosch Power Tools