Kenwood JMP600WH Instrucciones página 6

Misuse of your appliance can result in injury.
l
Do not let the cord touch hot surfaces or hang down where a
l
child could grab it.
Appliances can be used by persons with reduced physical,
l
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and if they
understand the hazards involved.
Only use the appliance for its intended domestic use.
l
Kenwood will not accept any liability if the appliance is subject
to improper use, or failure to comply with these instructions.
before plugging in
Make sure your electricity supply is the same as
l
the one shown on the underside of the appliance.
WARNING: THIS APPLIANCE MUST BE
l
EARTHED.
This appliance conforms to EC Regulation
l
1935/2004 on materials and articles intended to
come into contact with food.
before using for the first time
Wash the parts: see 'care and cleaning'.
key
pusher
1
lid with hopper
2
scroll
3
filter basket
4
rotating wiper holder
5
juicing bowl
6
pulp spout
7
pulp container
8
power unit
9
juice spout
bk
anti-drip stopper
bl
reset button
bm
On/Off/Reverse switch
bn
juice jug
bo
clip on sieve
bp
cleaning brush
bq
sorbet attachment (if supplied)
br
using your juicer
1 Fit the pulp stopper
underside of the juicing bowl
(B)
until secure .
2 Fit the juicing bowl
aligning the
the on the power unit with the (graphic) on the power unit
on turn it clockwise until the
on the power unit with the (graphic) on the power unit
(graphic) on the bottom of the bowl
3 Place the filter basket
(E)
.
5
(graphic) on the bottom of the bowl
unlock graphic
4 Lower the wiper holder assembly into the juicing
bowl and align the
unlock graphic
(F)
the power unit
lock graphic / Fit the lid onto the unit and click in
is locked into place.
5 Place the scroll
3
lock graphic / Fit the lid onto the unit and click into p
push down to secure
cannot be fitted if the scroll is not fully
lter holder assembly into the juicing bowl and align
(graphic) on the juicing bowl
pushed down.
6 Fit the lid onto the unit ensuring the
2
(graphic) on the juicing bowl
lines up with the
Then turn the lid clockwise until it clicks into
place and the
(I)
the power unit
into the feed tube.
7 Place the pulp container
spout and place the juice jug
7
juice spout . Ensure the anti-drip stopper
bk
is in the open position
There is a clip on sieve
l
used if a smooth juice is preferred and should
be emptied when full or after every 1kg of juicing.
Use the recommended usage chart as a guide for
l
juicing different fruits and vegetables.
3
with the (graphic) on the power unit
(A)
into the opening on the
and push in
6
(graphic) on the bottom of the bowl
to the power unit by
6
on the side of the bowl with
unlock graphic
(C)
. To lock the bowl
line up with the
lock graphic / Fit the lid onto the unit an
(D)
.
into the wiper holder
4
lter holder assembly into the juicing b
(graphic) on the juicing bowl
with the on the top of
. Ensure that the filter basket
switch graphic, on, o & reve
with the (graphic) on the power unit
into the filter basket and
lter holder assembly into the juicing bowl and a
(G)
. Note: the lid
(graphic) on the bottom of the bowl
unlock graphic
with the (graphic) on the power un
on top of the power unit
switch graphic, on, o & reverse
lines up with the on top of
lock graphic / Fit the lid onto the unit
(graphic) on the bottom of the bow
switch graphic, on, o & reverse
. Place the food pusher
lter holder assembly into the juicing
unlock graphic
under the pulp
8
under the
bo
(graphic) on the juicing bowl
lock graphic / Fit the lid onto the u
(J)
before juicing.
provided, this can be
bp
lter holder assembly into the juic
switch graphic, on, o & re
(graphic) on the juicing bowl
switch graphic, on, o &
with the (graphic) on
(graphic) on the botto
unlock graphic
lock graphic / Fit the li
lter holder assembly
(graphic) on the juicin
with the (g
switch grap
(graphic) o
unlock gra
(H)
.
lock graph
with the (grap
1
lter hold
(graphic) on th
(graphic) o
unlock graphic
bl
lock graphic /
lter holder as
(graphic) on th
swi