Publicidad
Idiomas disponibles
Idiomas disponibles
or electrical connections with grounding wire. The connections
must be properly installed and grounded.
Main parts of the product
(Fig.1 on page 3)
1. Door
2. Control panel
3. Plastic housing
4. Mesh (x1)
5. Bottom pad (x1)
6. Stainless steel grid (x7)
Remark: The content of this manual applies for all listed items
unless specified otherwise. The appearance may vary from the
shown illustrations.
Control panel
(Fig.2 on page 3)
A. Decrease setting (TEMP / TIME)
B. TEMP / TIME button
C. Increase setting (TEMP / TIME)
D. LED display
E. KEEP WARM button
F. FAST/RAW mode button
G. ON/OFF button
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Note: After cleaning the appliance, it must be switched ON (See
==> Operation instructions) for about 30 minutes with tempera-
ture set at 70°C. There is some odour or smoke evolved during
the first few cycles. This is normal and does not indicate any
defect or hazard. Make sure the appliance is well ventilated.
Operating instructions
• Place the appliance on a horizontal, stable, non-slip, and
heat-resistant surface.
• Position the food evenly on the trays, ensuring they do not
overlap. In order to have good ventilation inside the appliance,
10% of the tray's surface should be free from food.
• Remove any trays that are not being used. A total of 7 trays
can be used at the same time.
• When inserting the trays, ensure they are aligned with the
same side board correctly. Then, close the door firmly.
• Next, connect the power plug to a suitable electri cal pow-
er supply socket. There is a beep sound and all buttons are
lighted on for 3 seconds. Then, only TEMP / TIME button will
be blinked in blue; the LED screen is fully displayed and the
appliance is now in the STANDBY mode.
• Press the TEMP / TIME button to start the opera tion. All but-
tons on the control pan el will be lighted up in blue so the user
could adjust the timer and temperature or go to keep warm
or fast/raw mode. Press ON/OFF button without adjustment,
the machine will go to default mode. The default temperature
is 70°C and the default timer is 10hours.
Temperature setting
• Press TEMP / TIME button once in standby mode to check the
temperature setting, when the temperature is blinking in the
display, you can also press button + or - to increase or de-
crease operation temper ature setting. (Default temperature:
70°C, range: 35°C ~ 70°C, interval is 5°C).
• The user should press ON/OFF button to confirm the tem-
perature setting.
• If you want to check the temperature that was set, press
TEMP / TIME button once and the set temperature will be
shown on the LED display.
• During the operation process, you can check or change the
time and temperature setting by pressing the TEMP / TIME
button. And then press button + or - to increase or decrease
the temperature and time setting.
Time setting
• Press TEMP / TIME button twice in standby mode, then the
timer is blinking in the display, the user can press button +
or - to increase or decrease operation time. (Range: 00:30 ~
24:00, interval is 30 minutes).
• The user should press ON/OFF button to confirm the timer
setting.
• Then, the appliance will start operation and remaining time
will be shown on the LED display. The fan at the rear side of
the appliance will start rotation.
KEEP WARM mode
• The display will show "KEEP WARM" if pressing "KEEP
WARM" button. The machine will keep working for extra 24
hours in 35°C temperature after finishes dehydrating.
• When the countdown timer finishes, the display will show
88:88 and the heating element will switch off. The fan will
continue running for 10 seconds and the machine will beep 20
times to remind the user. After beeping 20 times, the machine
will go back to standby mode.
FAST/RAW mode
• In FAST mode, the temperature is 70°C and the timer is 10
hours. The display will show "FAST".
• In RAW mode, the temperature is 45°C and the timer is 24
hours. The display will show "RAW".
Switch to STANDBY mode
• If the user did not press ON/OFF button in 5 seconds after
setting, the machine will jump back to standby mode. Only
TEMP / TIME button will be blinked in blue and the LED
screen is fully displayed.
GB
7
Publicidad
