Publicidad
Idiomas disponibles
Idiomas disponibles
-For sanitation operations, biocidal
products that comply with European
regulation no. 582/2012 must be used.
►►2. UNPACKING
►2.1. Remove all packaging materials
used to wrap and deliver the appliance
and dispose of them in compliance with
the Standards in force.
►2.2. Extract all items from the packaging.
►2.3. Verify if damage has occurred during
transport. Immediately inform the dealer
where the appliance was purchased if this
appears damaged.
►►3. ASSEMBLY
(Fig. 1) The device is equipped with wheels
to facilitate handling. Depending on the
model, wheels can be found already in-
stalled or not. Components equipped with
relative nuts and bolts are found inside the
packaging.
►►4. OPERATION
WARNING: Thoroughly read the "INFOR-
MATION REGARDING SAFETY", before
switching the appliance on.
WARNING: Only use clean water to pre-
vent failures or other anomalies.
WARNING: Verify if your electronic sys-
tem is earthed correctly. Connection to
the mains must be made in compliance
with the National Standards in force. Only
power the appliance the with voltage and
frequency as specified on the nameplate.
NOTE: These models can be connected
to the water mains, by connecting the
pipe to the fitting (Fig. 10).
►►4.1. SWITCH-ON:
►4.1.1. Open the tank door (Fig. 2).
►4.1.2. Fill the tank with water (Fig. 3), the
water level must be between MIN and
MAX of the graduated scale (Fig. 4), so
as to avoid risks.
►4.1.3. Close the tank door (Fig. 5).
►4.1.4. Connect the power plug to the
mains (Fig. 6).
►4.1.5. Press the "ON/OFF"/"POWER" but-
ton to switch on the appliance (Fig. 9).
►►4.2.1. CONTROL PANEL AND
FUNCTIONS (Fig. 7):
►ON/OFF: Turns on or off the device.
►SPEED: Increases or decreases the
ventilation speed of the device. You can
choose from three speeds.
►COOL: Enables or disables the cooling
mode.
►SWING: Enables or disables the automat-
ic swing of the fins to direct the air flow.
►TIMER: Enables to activate or deactivate
the delayed switch-on or switch-off mode.
-Delayed switch-on: When the cooler is on,
press the "TIMER" button repeatedly until
the desired time is displayed (the number
flashes), then switch off the equipment.
-Delayed switch-off: When the cooler is
on, press the "TIMER" button repeatedly
until the desired time is displayed, then
the switch-off time is set.
NOTE: When the cooler emits an
acoustic beep, it means that the tank
is empty and must be filled again
("COOL" function). To deactivate the
acoustic beep, deactivate the "COOL"
function.
►►4.2.2. REMOTE CONTROL AND
FUNCTIONS (Fig. 8):
►POWER: Turns on or off the device.
►LOW - MID - HIGH: Increases or decreas-
es the ventilation speed of the device. You
can choose from three speeds: LOW, MID
and HIGH.
►COOL: Enables the cooling mode.
►WIND: Enables the ventilation mode
ONLY.
►SWING: Enables or disables the automat-
ic swing of the fins to direct the air flow.
►TIMER: Enables to activate or deactivate
the delayed switch-on or switch-off mode.
-Delayed switch-on: When the cooler is on,
press the "TIMER" button repeatedly until
the desired time is displayed (the number
flashes), then switch off the equipment.
-Delayed switch-off: When the cooler is
on, press the "TIMER" button repeatedly
until the desired time is displayed, then
the switch-off time is set.
en
Publicidad
