Bosch GDS Professional 18-210 C Manual Original página 18

18 | English
Cordless Impact Wrench
Data transfer
C)
Bluetooth®
Signal interval
D)
Max. signal range
A) Measured at 20–25 °C with rechargeable battery ProCORE18V 8.0Ah
B) Measured with GBA 18V 1.5Ah and GBA 18V 12 Ah.
C) The mobile terminal devices must be compatible with Bluetooth® Low Energy devices (version 4.1) and support the Generic Access Profile
(GAP).
D) The signal range may vary greatly depending on external conditions, including the receiving device used. The Bluetooth® range may be signi-
ficantly weaker inside closed rooms and through metallic barriers (e.g. walls, shelving units, cases, etc.).
Noise/vibration information
GDR 18V-210 C / GDX 18V-210 C:
Noise emission values determined according to
EN 62841-2-2.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 96 dB(A); sound power level
107 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
GDS 18V-210 C:
Noise emission values determined according to
EN 62841-2-2.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 97 dB(A); sound power level
108 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty
h
K determined according to EN 62841-2-2:
Impact tightening of fasteners of the maximum capacity of
the tool:
2
GDR 18V-210 C: a = 10 m/s , K = 1.5 m/s
h
2
GDX 18V-210 C: a = 9 m/s , K = 1.5 m/s
h
GDS 18V-210 C: a = 12.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
1 609 92A 7X4 | (17.10.2022)
GDR 18V-210 C
Bluetooth® 4.1
(Low Energy)
s
m
2
2
2 2
, K = 1.5 m/s
GDX 18V-210 C
Bluetooth® 4.1
(Low Energy)
8
30 30
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Charging the Battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the Battery
The battery (4) is equipped with two locking levels to pre-
vent the battery from falling out when pushing the battery re-
lease button (5) unintentionally. As long as the battery is in-
serted in the power tool, it is held in position by means of a
spring.
To remove the battery (4), press the release button (5) and
pull the battery out of the power tool. Do not use force to
do this.
Battery charge indicator
The green LEDs on the battery charge indicator indicate the
state of charge of the battery. For safety reasons, it is only
GDS 18V-210 C
Bluetooth® 4.1
(Low Energy)
8 8
30
Bosch Power Tools