Publicidad
ESG 105CFM
1
2
ERROR CODE:
****
3
BT
P 3
bar
P 3
bar
4a
USER 3:
RD3
Doppelklick
4b
USER SELEC T 3:
RD3
E i nfachklick
3 sec.
4c
USER SELEC T :
RD3
D o ppelklick
4d
USER SELEC T :
RD3
D o ppelklick
Klauke i-press
Klauke i-press
www.klauke.com/connectivity
www.klauke.com/connectivity
Klauke i-press
Klauke i-press
For US and Canada only
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée
aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le foncti-
onnement.
NOTICE:
Changes or modifi cations made to this equipment not expressly approved by Klauke may void the FCC authorization to operate this equipment.
HE.17172_F © 05/2016
5
6
Error code
7
*1
*2
Bluetooth (if connected)
Battery charging level
Current pressure
Pressure max.
Doubleclick
Singleclick
enter menue
Doubelclick
select
Doubelclick
confi rmed
additional profi les:
ARS Single Click
ARS Double Click
MRS+ Single Click
MRS+ Double Click
®
®
Software
Software
®
®
App
App
WORK
SERVICE
NEXT
SERVICE:
Cycles
9826 OP
(until next service)
s
Since manufacturing:
TOTAL:
operating houres
t = 0
07
h
.
Q = 21
12 Ah
Capacity
.
n = 174
# crimps
*2
≤ 20 sec.
≤ 20 sec.
> 20 sec.
> 20 sec.
≤ 20 sec.
≤ 20 sec.
REPEAT
REPEAT
DON´T DO
*1
Error codes/ Fehlermeldungen:
1 Overcurrent fuse
2 Overcurrent comparator
3 Overheat board
4 Overheat battery
5 Battery empty, operation stop
6 Faulty crimp motor in operation
7 Faulty crimp motor not in operation
8 Low battery
9 Battery empty
10 RTC battery low
12 Service necessary
13 RTC not found
14 BT unit not found
15 Mobile unit not found
16 Pressure sensor not found
17 Burst pressure exceeded
18 Battery temperature too low
19 Battery reserves
20 Overcurrent fuse (I)
21 Remote Control Battery Low!*
22 Service necessary SAST1
23 Service necessary SAST2
24 Service necessary SAST3
25 Remote mode: tool trigger not actuated*
27 Overheat motor
28 Service necessary: Pressure low
29 Service necessary: Pressure high
1 Überstromsicherung
2
Überstromsicherung durch Komparator
3 Boardtemperatur zu hoch
4
Akkutemperatur zu hoch
5
Akkuspannung zu gering
6
Fehlpressung bei laufendem Motor
7
Fehlpressung bei stehendem Motor
8
Niedrige Akkuspannung
9 Akku leer
10
RTC-Batterie leer
12 Service nötig
13 RTC nicht verfügbar
14
BT-Modul nicht verfügbar
15 Modul nicht verfügbar
16
Drucksensor nicht verfügbar
17
Berstdruck überschritten
18
Akkutemperatur zu gering
19 Batteriereserven zu gering
20 Überstromsicherung (I)
21 Fernbedienung-Batterie schwach*
22 Service notwendig SAST1
23 Service notwendig SAST2
24 Service notwendig SAST3
25 Remote-Modus: WZ-Taster nicht betätigt*
27 Motortemperatur zu hoch
28 Service notwendig: Druck niedrig
29 Service notwendig: Druck hoch
(2Hz)
* remote control tools only /
nur bei fernbedienungsfähigen Werkzeugen
General
safety rules
V
Publicidad
