Prince Toys Pala cargadora CAT Instrucciones De Uso página 8

on even grounds and safe areas.
7.Do not allow another child to push the ride-on car while your child uses it.
8.Check regularly the condition of each part. In case of damage there is a risk of injuring your child.
9..Check regularly whether the nut and bolt on the steering wheel are fixed tightly and do not represent any danger.
10.If the product is not assembled properly this may lead to danger.
11.Do not allow the child to use the ride-on car barefoot.
12.Do not allow the child to remove the stickers, if there are any glued to the product, and to swallow them.
13.The raw materials and colors, used for producing the products, are suitable and safe for the children's health.
IV. HANDLING OF THE BATTERY
1.The batteries should be handled by an adult only. The batteries are not toys. Do not allow the children to play with
the batteries.
2.Always use the same type of batteries. Do not mix alkaline batteries with standard (Carbon - Zinc) ones, or with
rechargeable (Nickel – Cadmium) ones.
3.The exhausted batteries must be removed immediately from the toy. If you will not use the toy for a long time,
remove the batteries from it before storing it.
4.When changing the batteries, always replace all the batteries. Never mix old batteries with new ones. Children
should not be present during the changing of the batteries.
5.Do not throw the exhausted batteries away with the household waste. They contain components that may hard
the environment. These components are recyclable. Dispose of such waste only at designated recycling sites/
landfills.
6.Do not throw the batteries in fire. Risk of explosion or leak.
7.Do not modify the electric circuit and do not add any other parts to it.
8.Do not shorten the battery terminals.
9.Do not charge batteries, which are not rechargeable.
10.If you use rechargeable batteries, first take out the batteries from the product and then charge them. The
charging should be supervised by an adult only.
11.11.Use batteries with the same size as marked on the battery compartment or as written in the manual.
12.12.Alkaline batteries are recommended.
V. PRODUCT PARTS
1.Dozer bucket – 1 pc; 2. Arm and handlebars for vehicle control – 1 pc.; 3. Steering wheel – 1 pc; 4.Backrest – 1 pc;
5. Car body – 1 pc; 6. Tool for fixing – 1pc.; 7. Axle – 1pc.; 8. Screw – 5 pcs (1 replacement piece); 9.J-shaped front
fork – 1 pcs
VI. ASSEMBLY STEPS
Read the instructions carefully before you start the assembly of the product. Follow exactly the individual steps for
assembly and inspect after each action, whether you have fixed the individual parts tightly.
1.Step 1 – See Figure1: Take the steering wheel and have the bolt and nut attached to it removed using a
screwdriver. 2.Step 2 – See Figure 2: Slide the front fork through the opening in the bottom of the car body. Its
curved end must be attached to the opening of the plastic part connecting the front axles.
3.Step 3 – See Figure 3: Attach the steering wheel to the front fork, coming out of the car body. Align the openings
of the fork and steering wheel intended for the fixing bolt. Slide through these openings the bolt and fix it using nut
and screw.
4.Step 4 – Figure 4: Attach the bucket to the arm and with 4 fixing screws and a screwdriver fix them well.
5.Step 5 – Figure 5: Insert the assembled arm with the bucket into the front of the body of the car. Align the
openings on the arm with those on the body intended for the axle. Slide the axle through these openings and
tighten using the tightening tool.
6.Step 6 – Figure 6: Attach the backrest to the rear car body and press down carefully until it is fixed.
Battery change: The battery compartment is on the steering wheel. Use a screwdriver to remove the screw from
the battery compartment cover. Lift the cover and place 2 batteries 1.5V AAA according to the polarity „+" / „-"
marked in the compartment. Reattach the cover and fix it using the screws and screwdriver. Note! The batteries are
not included in the package. WARNING! Children should not be present when placing the batteries.
VII. PRODUCT FUNCTIONS
1.See FIGURE U-1: Push forward the left handlebar and it will move forward.
2.See FIGURE U-2: Push forward the right handlebar and the bucket will tilt forward to pour the contents into it.
3.See FIGURE U-3: The steering wheel is equipped with buttons for horn sounds.
7