TELECO AUTOMATION TVRCL868A02F7 Manual Del Usuario página 8

Warnings
IMPORTANT! READ CAREFULLY THIS INSTRUCTIONS BEFORE INSTALLING AND
COMMISSIONING THE PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PRODUCT INSTALLATION
The product at issue must be installed, commissioned and maintained only by licensed and authorised people, respecting
the laws concerning the electrical installations. Not conforming installations, wrong adjustments or product alterations
may cause fire, electric shock, or personal injuries. The manufacturer is not responsible for any damage due to wrong
installation or improper use.
MOUNTING LOCATION AND MODALITY
The product must be mounted applying the following indications carefully: it must be fixed on surfaces which cannot be
damaged by the high temperature; it must be placed in a well ventilated location; it cannot be hermetically closed; it must
be fixed vertically, with cable glands downward; connection cables must be protected against any accidental impacts,
using proper pipes; do not cover the product; do not use or store flammable materials close to the product.
ELECTRICAL CONNECTIONS
All the connections must be rated for a single-phase 110/230Vac power supply, with the relative Earth connection.
For the disconnection from the power line, use an all-pole switch with contacts having a dimension of at least 3,5mm.
Arrange all the necessary safety devices and use only materials complying with the standard of electrical installations.
Signal and power voltage wiring (110/230Vac) must be separated one from the other. The cable must have a section
properly rated according to the load connected and a nominal temperature range (T) up to 90°C.
The product used at maximum power must have power supply input and load connection output cables with a minimum
section of AWG 10.
The protective device (In=30A) must protect the building from overcurrents and short circuits.
A readily accessible disconnect device shall be incorporated in the building installation wiring.
Attention: If any cable is damaged, it must be immediately replaced by a qualified person in order to avoid any hazard.
SAFETY INFORMATION
This appliance is not intended for use by people (including children) with reduced physical, sensory or mental capabilities, or
not properly informed about the product's characteristics or the possible hazards it can cause. Children should be carefully
supervised when they are in the area of the product. Do not touch the electronic board with wet hands, any metallic or
flammable objects. Do not operate in the high voltage area of the electronic board, when it is supplied. Use the product
only in combination with devices which can guarantee a safe extended time functioning. The radio signal reception of the
device could be disturbed by the presence of electrical disturbances being transmitted by other appliances working on the
same frequency or if the product is somehow shielded by metal parts.
PRODUCT DISPOSAL
The manufacturer, Teleco Automation s.r.l, declares that the type of radio equipment is compliant with Directive 2014/53/
EU. The full text of the EU compliance declaration is available at the following Internet address: www.telecoautomation.
com/ce. INFORMATION TO USERS under art. 14 of the 2012/19/EU DIRECTIVE OF THE EUROPEAN PARLIAMENT AND
COUNCIL of 4 July 2012 on waste electrical and electronic equipment (WEEE). The crossed bin symbol on the equipment,
or its packaging, indicates that the product must be collected separately from other waste at the end of its useful life and not
with mixed urban waste. Please contact your municipality, or local authority, for all information regarding the waste sorting
systems available in the area. The retailer is obliged to collect the old equipment free-of-charge when the customer buys
a new equivalent equipment. This is to encourage correct recycling/disposal. Appropriate waste sorting for the subsequent
recycling,reatment and disposal in an environmentally sound way of the disused equipment avoids negative effects on the
environment or human health and favours the re-use or recycling of the equipment's materials.
In the view of a constant development of their products, the manufacturer reserves the right for changing
technical data and features without prior notice.
Technical specifications
-Power supply
-Single Output (cos φ = 1)
-Max. output power
(Resistive load)
-Dimensions
-IP
110-230Vac (30A) -Operating temperature range
110-230Vac (15A) -Reception frequency
3400W (@ 230Vac)
1500W (@ 110Vac) -Radio memory capability
205 x 145 x 85 mm (transmitters)
54
8
-20° +50°C
868.3 MHz (TVRCL868A02F7)
916 MHz (TVRCL916A02F7)
42