Publicidad
Idiomas disponibles
Idiomas disponibles
9.Check regularly whether the nut and bolt on the steering wheel are fixed tightly and do not represent any danger.
10.If the product is not assembled properly this may lead to danger.
11.Do not allow the child to use the ride-on car barefoot.
12.Do not allow the child to remove the stickers, if there are any glued to the product, and to swallow them.
13.The raw materials and colors, used for producing the products, are suitable and safe for the children's health.
IV. HANDLING OF THE BATTERY
1.The batteries should be handled by an adult only. The batteries are not toys. Do not allow the children to play with the
batteries.
2.Always use the same type of batteries. Do not mix alkaline batteries with standard (Carbon - Zinc) ones, or with
rechargeable (Nickel – Cadmium) ones.
3.The exhausted batteries must be removed immediately from the toy. If you will not use the toy for a long time, remove
the batteries from it before storing it.
4.When changing the batteries, always replace all the batteries. Never mix old batteries with new ones. Children should
not be present during the changing of the batteries.
5.Do not throw the exhausted batteries away with the household waste. They contain components that may hard the
environment. These components are recyclable. Dispose of such waste only at designated recycling sites/ landfills.
6.Do not throw the batteries in fire. Risk of explosion or leak.
7.Do not modify the electric circuit and do not add any other parts to it.
8.Do not shorten the battery terminals.
9.Do not charge batteries, which are not rechargeable.
10.If you use rechargeable batteries, first take out the batteries from the product and then charge them. The charging
should be supervised by an adult only.
11.Use batteries with the same size as marked on the battery compartment or as written in the manual.
12.Alkaline batteries are recommended.
V. PRODUCT PARTS
1.Car body – 1 pc; 2.Steering wheel – 1 pc; 3.Backrest – 1 pc; ; 4. Safety board – 1 set; 5. Decorative spare tyre – 1 pc;
6.Thumb latch – 2 pcs; 7. Parent control handle– 1 pc; 8. Connecting tube for assembling the parent control handle – 1 pc;
9.Canopy – 1 pc; 10.Canopy stand – 1 pc; 11. Safety bar fixed part – 1 pc; 12. J-shaped stick – 1 pc; 13.Bolt M5X28 – 4 pcs
(1 replacement piece); 14.Nut M5 – 4 pcs (1 replacement piece); 15.Screw – 3 pcs (1 replacement piece).
VI. ASSEMBLY STEPS
Read the instructions carefully before you start the assembly of the product. Follow exactly the individual steps for
assembly and inspect after each action, whether you have fixed the individual parts tightly.
1.Step 1: Installing the steering support to the car body – Figure1: Insert the steering axle through the respective
opening in the front bottom part of the car body, making sure it is fitted correctly in the right position as shown in Figure
2.Step 2: Installing steering wheel - Figure 2: Place the safety board holder on top of the steering shaft coming out of the
body. Take the steering wheel and remove the retaining screw and nut. Insert the steering wheel into the holder opening
so that the steering shaft fits into the steering wheel hole. Align the openings on the steering shaft and steering wheel
that are intended for the fixing screw. Push the screw through them and secure it using a nut and screwdriver. Do not
overtighten to avoid damaging any of the parts. The sealed part of the steering shaft must enter the hole in the plastic
part to which the front axles are attached.
3.Step 3:Installing the decorative spare tire – Figure 3: Place the spare tire into the backside of the car body as shown in
figure 3. Fix with the two screws using a screwdriver.
4.Step 4:Installing the backrest – Figure 4: Place the backrest over the openings in the back part of the car body. Press
the backrest downwards carefully in order to be secured in the respective openings. Make sure that the backrest is
secured.
5.Step 5:Installing the parental control handle – Figures 5 and 6: Assemble the parental control handle by attaching it to
the connecting tube using two bolts and a nuts (see figure 5). Remove the clamping ring at the end of the tube. Insert the
assembled parental control handle into the slot in the back of the backrest. Reverse the car body and insert the locking
ring as shown in Figure 6.
6. Step 6: Installing the safety board – Figure 7: It is made of 2 rails. The rear parts of the rails must be attached to the
holders on the backrest. Insert the locking mechanisms into the openings of the partitions to fix them to the backrest.
Their front parts must be gripped to the holder under the steering wheel. Press gently until they are fixed. You will hear a
clicking sound.
7.Step 7: Installing the canopy – Figures 8 and 9: Attach the canopy to the stand using a bolt and nut (see Figure 8). Insert
the assembled stand with the canopy into the backrest slot, press to secure ( see figure 9).
8.Step 8:Replacing batteries: The battery compartment is on the steering wheel. Use a screwdriver to remove the screws
6
Publicidad
