Whirlpool WDF332PAM Serie Manual Del Usuario página 2

PRODUCT MODEL NUMBERS
WDF110PAB WDF340PAM
WDF111PAB WDF520PAD
WDF120PAF WDF540PAD
WDF121PAF WDF545PAF
WDF130PAH WDT530HAM
WDF131PAH WDT540HAM
WDF320PAD WDT710PAH
WDF330PAH WDT720PAD
WDF331PAH WDT730HAM
WDF331PAM
DRAIN REQUIREMENTS
■ A new drain hose is supplied with your dishwasher. If drain
hose is not long enough, use a new drain hose with a
maximum length of 12 ft (3.7 m) that meets all current
AHAM/ IAPMO test standards, is resistant to heat and
detergent, and fi ts the 1" (25 mm) drain connector of the
dishwasher. See the "Tools and Parts" section at the front of
the guide for part details and orders.
■ Make sure to connect drain hose to waste tee or disposer
inlet above drain trap in house plumbing and 20" (508 mm)
minimum above the fl oor. It is recommended that the drain
hose either be looped up and securely fastened to the
underside of the counter or be connected to an air gap.
■ Make sure to use an air gap if the drain hose is connected to
house plumbing lower than 20" (508 mm) above subfl oor or
fl oor.
Use of air gap
Air gap
■ If required, the air gap should be installed in accordance with
the air gap installation instructions. When you are connecting
the air gap, a rubber hose (not provided) will be needed to
connect to the waste tee or disposer inlet.
■ Use 1/2" (13 mm) minimum I.D. drain line fi ttings.
WATER SUPPLY REQUIREMENTS
■ This dishwasher has a water heating feature and also requires
a connection to a hot water supply line.
■ A hot water line with 20 psi to 120 psi (138 kPa to 862 kPa)
water pressure can be verifi ed by a licensed plumber.
■ 120°F (49°C) water at dishwasher.
Because Whirlpool Corporation policy includes a continuous commitment
to improve our products, we reserve the right to change materials and
specifications without notice.
W11542837B
Undercounter Dishwasher
■ 3/8" (95 mm) O.D. copper tubing with compression fi tting or
fl exible braided water supply line. See the "Tools and Parts"
section at the front of the guide for part details and orders.
WDT730PAH
WDT735PAG
NOTE:
WDT735PAH
recommended.
WDP540HAM
WDP560HAM
■ A 90° elbow with 3/4" (95 mm) hose connection with rubber
WDP730HAM
washer. See the "Tools and Parts" section at the front of the
WDF332PAM**
guide for part details and orders.
WDF341PAP**
■ Do not solder within 6" (152 mm) of the water inlet valve.
WDT531HAP**
■ If installed in new construction, make sure the house water
supply lines have been fl ushed prior to connecting the
dishwasher to remove any debris that may exist in the supply
line.
NOTE:
recommended to install a new water line (see the "Tools and
Parts" section at the front of the guide for part details) and
drain hose (supplied) with the new dishwasher.
ELECTRICAL REQUIREMENTS
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
You Must Have:
■ 120 V, 60 Hz, AC only, 15 A or 20 A, fused electrical supply.
■ Copper wire only.
■ A maximum of 2 fi eld wiring supply conductors (12 AWG
largest size) plus 1 grounding conductor are permitted in the
terminal box.
We Recommend:
■ A time-delay fuse or circuit breaker.
■ A separate circuit.
If Connecting Dishwasher with a Power Cord:
■ Use UL Listed power cord kit marked for use with
dishwasher. See the "Tools and Parts" section at the
front of the guide for part details and orders.
■ Plug into a grounded 3 prong outlet. Outlet must meet
all local codes and ordinances.
Dimensions are for planning purposes only. For complete details, see
Installation Instructions packed with product. Specifications subject to
change without notice.
1/2" (13 mm) minimum plastic tubing is not
If replacing an existing dishwasher, it is
WARNING
Electrical Shock Hazard
1