Descargar Imprimir esta página

SOLAC BV5723 Instrucciones De Uso página 12

Batidora de vaso

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 1
Before switching on the appliance, always
make sure that the lid is correctly fitted/closed
and that the measuring beaker is in well insert-
ed into the lid.
Cut fruit into small pieces before putting it into
the filter.
Soak dry ingredients, such as legumes or soy
beans, before putting them into the filter.
USE:
The filter prevents fruit skin and pips from mix-
ing with the drink.
Once the jar (C) is fitted correctly onto the mo-
tor body (A) (Fig. 1).
Place the filter (G) around the blade (D)
(Fig. 2).
Make sure that the slots on the filter fit perfectly
into the spigots on the blender jug.
Place the lid on the jug.
PLEASE NOTE: Be sure to put the lid on the
jug so that the drink is served through the filter
in the lid.
Cut fruit into small pieces or soak dry ingredi-
ents before putting them into the filter.
Place the ingredients in the filter and pour wa-
ter or other liquid into the jug through the hole
in the lid.
Insert the measuring beaker into the lid
(Fig. 1).
Connect the appliance to the mains.
Choose the desired speed and start blending.
NOTE: When processing large quantities, it is
advisable not to put all of the ingredients into
the filter at the same time. Start with a small
amount and let the appliance run for a few
seconds. Then switch off the appliance and
add another small amount, without filling be-
yond the top of the sieve mesh. Repeat this
procedure until all the ingredients have been
processed. Always leave the blender jug lid on
while it is operating.
ONCE YOU HAVE FINISHED USING THE FILTER:
Switch the appliance off and remove the jug
from the motor body.
Serve the drink through the spout on the jug,
without removing the lid, measuring beaker or
filter. Be sure to put the lid on the jug so that
the drink is served through the filter in the lid.
Clean filter immediately after using it.
CLEANING
Disconnect the appliance from the mains and
allow it to cool before undertaking any clean-
ing task.
Clean the equipment with a damp cloth with a
few drops of washing-up liquid and then dry.
Do not use solvents, or products with an acid
or base pH such as bleach, or abrasive prod-
ucts, for cleaning the appliance.
Do not let water or any other liquid get into the
air vents to avoid damage to the inner parts of
the appliance.
Never submerge the appliance in water or any
other liquid or place it under running water.
During the cleaning process, take special
care with the blades, as they are very sharp.
It is advisable to clean the appliance regularly
and remove any food remains.
The following pieces may be washed in a
dishwasher (using a soft cleaning program):
-
Jug (without its blades).
-
Removable filter.
-
Lid.
-
Measuring cup.
The draining/drying position of the articles
washable in the dishwasher or in the sink must
allow the water to drain away easily.
Then dry all parts before its assembly and
storage.
SELF-CLEANING FUNCTION:
Put water and a small amount of washing up
liquid in the jar.
Select the function "turbo".
REMOVABLE
BLADES
CLEANING (JAR BLENDER ONLY)
Loosen the blade fixing ring by turning it in
clockwise direction. (Fig.3).
Remove the blade fixing ring, blade set, seal-
ing ring and clean them.
After cleaning, replace the blade set and turn
blade fixing ring in opposite direction.
ANOMALIES AND REPAIR
Take the appliance to an authorised technical
support service if product is damaged or other
problems arise. Do not attempt to disassemble
or repair the appliance yourself as this may be
dangerous.
EN
FOR
EFFECTIVE

Publicidad

loading