Bosch GSR Professional 18V-90 C Manual Original página 11

Follow the instructions on correct disposal.
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Inserting the Bluetooth® Low Energy Module
GCY 42 (Accessory)
Read the corresponding operating instructions for informa-
tion about the Bluetooth® Low Energy Module GCY 42.
Changing the tool (see figure A)
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
The drill spindle is locked when the on/off switch (12) is not
pressed. This makes it possible to change the application
tool in the drill chuck quickly, conveniently and easily.
Open the keyless chuck (2) by turning it in the direction of
rotation ➊ until the tool can be inserted. Insert the tool.
Firmly tighten the keyless chuck (2) by turning it by hand in
the direction of rotation ➋. This will automatically lock the
drill chuck.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Certain dust, such as oak or beech dust, is considered carci-
nogenic, especially in connection with wood-treatment ad-
ditives (chromate, wood preservative). Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the ma-
terials to be worked.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Operation
Starting Operation
Setting the rotational direction (see figure B)
The rotational direction switch (11) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (12) is being pressed.
Bosch Power Tools
Rotate clockwise: Slide the rotational direction
switch (11) on both sides until it stops in the
tion.
Rotate anti-clockwise: Slide the rotational direction
switch (11) on both sides until it stops in the
tion.
Setting the operating mode
Drilling
GSR 18V-90 C
Set the torque presetting ring (3) to the
"drilling" symbol.
GSB 18V-90 C
Set the operating mode presetting ring (4) to
the "drilling" symbol.
Screwdriving
GSR 18V-90 C
Set the torque presetting ring (3) to the re-
quired torque.
GSB 18V-90 C
Set the operating mode presetting ring (4) to
the "screwdriving" symbol.
Set the torque presetting ring (3) to the re-
quired torque.
Impact drilling
GSB 18V-90 C
Set the operating mode presetting ring (4) to
the "impact drilling" symbol.
Switching on/off
To start the power tool, press and hold the on/off switch
(12).
The LED (18) lights up when the on/off switch (12) is lightly
or fully pressed, meaning that the work area is illuminated in
poor lighting conditions.
To switch off the power tool, release the on/off switch (12).
Adjusting the speed
You can adjust the speed of the power tool when it is on by
pressing in the on/off switch (12) to varying extents.
A light pressure on the on/off switch (12) results in a low ro-
tational speed. Increased pressure on the switch causes an
increase in speed.
Preselecting torque (applies to screwdriving mode)
When the precision clutch is activated, you can pre-set the
required torque over 20 increments using the torque pre-
setting ring (3). Once the set torque has been reached, the
application tool will be stopped. When the precision clutch is
deactivated, the clutch will be released and the application
tool will not be stopped.
Mechanical gear selection
Only operate the gear selector (5) when the power
u
tool is not in use.
First gear:
English | 11
posi-
posi-
1 609 92A 91H | (24.08.2023)