Metabo KHE 2660 Quick Manual De Instrucciones Original página 8

en
ENGLISH
Original operating instructions
1. Declaration of Conformity
On our own responsibility, we hereby declare that
this drilling and chisel hammer, identified by type
and serial number *1), meets all relevant
requirements of directives *2) and standards *3).
Technical documents for *4) - see page 3.
For UK only:
We as manufacturer and authorized person to
compile the technical file, see *4) on page 3,
hereby declare under sole responsibility that these
drilling and chisel hammer, identified by type and
serial number *1) on page 3, fulfill all relevant
provisions of following UK Regulations S.I. 2016/
1091, S.I. 2008/1597, S.I. 2012/3032 and
Designated Standards EN 60745-1:2009+A11:
2010, EN 60745-2-6:2010, EN IEC 63000:2018.
2. Specified Conditions of Use
The rotary and chipping hammers are suited, with
appropriate accessories, for working with hammer
drill bits and chisels in concrete, stone and similar
materials and with core bits in tiles and similar, as
well as drilling without impact in metal, wood, etc
and for screwdriving.
The user bears sole responsibility for any damage
caused by inappropriate use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.
3. General Safety Information
For your own protection and for the
protection of your power tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Reading the operating
instructions will reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety
warnings and instructions may result in electric
shock, fire and/or serious injury.
Keep all safety instructions and information for
future reference.
Pass on your power tool only together with these
documents.
4. Special Safety Instructions
Wear ear protectors. Exposure to noise can cause
hearing loss.
Use the additional handle supplied with the
tool. Loss of control can cause personal injury.
Hold the power tool by the insulated gripping
surfaces when performing an operation where
the cutting accessory may contact hidden
8
wiring or its own cord. A cutting accessory
contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the
operator an electric shock.
Always work with the additional handle correctly
installed.
Always hold the machine with both hands at the
intended handles, take a secure stance and
concentrate on the work.
Always wear protective goggles, gloves, and sturdy
shoes when working with this tool.
Ensure that the spot where you wish to work is free
of power cables, gas lines or water pipes (e.g.
using a metal detector).
If the safety coupling responds, switch off the
machine immediately.
Do not touch the rotating tool!
Secure the workpiece to prevent slipping or rotation
(e.g. by securing with screw clamps).
Remove chips and similar material only with the
machine at a standstill.
Caution must be exercised when driving screws into
hard materials (driving screws with metric or
imperial threads into steel)! The screw head may
break or a high reverse torque may build up on the
handle.
Pull the plug out of the socket before making any
adjustments, changing tools, carrying out
maintenance or cleaning.
Avoid inadvertent starts by always unlocking the
switch when the plug is removed from the mains
socket or whenever the power fails.
A damaged or cracked additional handle must be
replaced. Never operate a machine with a defective
additional handle.
Safety clutch: f the tool jams or catches, the power
supply to the motor is restricted. Due to the strong
force which can arise, always hold the machine with
both hands using the handles provided, stand
securely and concentrate.
Reducing dust exposure:
WARNING - Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
- Lead from lead-based paints,
- Crystalline silica from bricks and cement and
other masonry products, and
- Arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.