Descargar Imprimir esta página

AEG VS4-1-4AG Guia De Inicio Rapido página 2

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 6
EN - Safety
Precautions
Please carefully read all the
instructions before using this ap-
pliance and save for future use.
Make sure before plugging in
the machine that the cover top
is unlocked. Always unplug from
the mains supply when the appli-
ance is not in use and before
cleaning.
This appliance is not a toy, when
used by or near children, close
attention is necessary. Store this
appliance in a safe place, out of
the reach of children.
Only use original parts from AEG.
Always check the appliance, the
cord and the switch panel before
use. If the cord is damaged, it
must be replaced by a profes-
sional.
Keep away from moving parts.
Do not touch the heating
element when it is hot.
Do not try to repair this appli-
ance by yourself.
Don't use the appliance if it has
fallen or appeared to be dam-
aged.
Avoid pulling or carrying by the
cord, using cord as a handle, get-
ting the cord stuck somewhere,
or pulling cord around sharp
edges or corners. Do not operate
appliance when cord / plug is
wet.
Keep away from hot gas, heated
oven, electric burner or any other
hot surfaces. Do not use this
appliance on wet or hot surface
or near a heat source.
It's better not to use an extension
cord with this unit. However,if
one is used, it must have a rating
equal to or exceeding the rating
of this appliance.
When unplugging the machine
to avoid any injury, please grasp
the plug not the cord.
Before plugging appliance in or
operating, make sure your hands
are dry and safe to do the
actions.
When it is in "ON" or working
position, always be on a stable
surface, such as table or counter.
No need to use any lubricant,
such as lubricating oils or water,
on this appliance.
Do not immerse any part of this
appliance, power cord or plug in
water or any other liquid.
The appliance is for domestic use
only.
This appliance is not intended for
use by persons (including chil-
dren) with reduced physical,
sensory or mental capabilities, or
lack of experience and knowl-
edge, unless they have been
given supervision or instruction
concerning use of the appliance
by a person responsible for their
safety.
Close supervision is required
when this product is used near
children.
If the supply cord is damaged, It
must be replaced by the manu-
facturer, its service agent or
similarly qualified persons in
order to avoid a hazard.
To reduce the risk of electric
shock, this product has a polar-
ized plug (one blade is wider
than the other). This plug is
intended to fit in a polarized
outlet only one way. When the
plug does not fit fully in the
outlet, reverse the plug. When it
still does not fit, contact a quali-
fied electrician to install the
proper outlet.
Do not change the plug in any
way.
If the appliance is used for other
purposes than intended, or is it
not handled in accordance with
the instruction manual, the full
responsibility for any conse-
quences will rest with the user.
Any damages as a consequence
of the above to the product are
not covered by the warranty.
Troubleshooting
1. Nothing happens when I try
to vacuum package
Check that the vacuum sealer is
connected to a working plug
Make sure bag is placed correctly
in the vacuum chamber and
beneath the air intake
2. Air is not removed from the
bag completely
Make sure the open side of bag
is resting entirely inside vacuum
chamber area.
Check sealing strip, heating
element surface, and the foam
gasket beneath the lid for debris
and position. Make sure no
breaking or distortion of the
foam seal gaskets on both the
cover and on the base around
the vacuum chamber. Wipe clean
and smooth them back into
place.
Vacuum bag may have a leak.
Reseal or use another bag.
Ensure top cover is pushed down
and locked on both ends of the
machine at the beginning of the
operation before starting the
vacuuming process.
Leaks caused by wrinkles, debris
crumbs, grease or liquids from
the bag. Reopen bag, wipe the
top inside of the bag and
smooth it out along the sealing
strip before resealing.
3. The machine does not turn
to seal after vacuuming
The machine will not turn to seal
automatically if the vacuum
pressure inside the bag is not
able to reach to the predeter-
mined vacuum pressure. Check
sealing strip and foam gasket
beneath the lid for debris, wipe
clean and try again.
Make sure no breaking or distor-
tion of the foam seal gaskets on
both the cover and on the base

Publicidad

loading