Craftsman 351.181710 Manual Del Operador página 3

DESCRIPTION
The Craftsman _/4" Crown Stapler drives %' crown, 18 gauge
staples from 3/8" to 1_/4"long. Oilless design eliminates daily oil-
ing and oil stains on workpiece. Die cast magnesium body with
textured rubber grip minimizes operator fatigue. Large capacity,
bottom loading magazine with positive, quick action latch
makes loading easy. Stapler features rear exhaust, single and
rapid-fire operation, adjustable depth of drive control, rubber
nose tip and storage case. Safety feature disables tool unless
contact trip is pressed against workpiece. Tapered nosepiece
provides operator with greater visibility for precise fastener
placement. Rigid nosepiece reduces jamming. The _/4" Crown
Stapler is excellent for furniture making, picture framing, uphol-
stery and cabinetry.
SPECIFICATIONS
Capacity ................................ 100 staples
Staple crown width ................................ '/4"
Staple lengths .............................. 3/8to 1W'
Staple size .................... 18 gauge (.049" x .040")
Operating pressure ........................ 60-100 PSI
Air inlet .................................... _/4"N.P.T.
Length ........................................ 9W'
Height ........................................ 77/8 ''
Width ........................................ 23/_''
Weight ..................................... 2.6 Ibs.
STAPLES
18333 _Box of 5000) .................. '/4" crown, _/2" long
19177 _Box of 1000) .................. '/4" Crown, _/2" long
18334 _Box of 5000) .................. _/4"crown, 3/4"long
19178 _Box of 1000) .................. _/4"crown, 3/4"long
18336 _Box of 5000) .................. '/4" crown, 7/8"long
19179 _Box of 1000) .................. _/4"crown, 7/8"long
18371 Box of 4000) .................. _/4" crown, 1" long
19180 _Box of 1000) .................. _/4" crown, 1" long
18372 _Box of 4000) ................. _/,"crown, 1_/8" long
18373 _Box of 4000) ................. _/4" crown, 1_/4" long
.AIR SUPPLY LINE
Refer to Figure 1.
DANGER: Do not use oxygen, carbon dioxide, high-pressure
compressed gas or bottled gases as the power source for this
tool. The tool will explode and serious personal injury could
result.
° The air tool operates on compressed air at pressures from
60 to 100 PSI.
° Never connect the tool to air pressure which could poten-
tially exceed 200 PSI. Use only clean, dry, regulated air
within rated range as marked on tool.
Air Delivery Required: 0.85 SCFM @ 90 PSI
(30 shots per minute).
WARNING: Keep hands and body away from discharge area
of tool when connecting air supply. Always disconnect tool
from air supply when servicing or adjusting tool and when tool
is not in use.
° Air operated tools require clean, dry, lubricated com-
pressed air to ensure top performance, low maintenance
and long life.
• Dirt and abrasive materials present in all air lines will dam-
age tool O-rings, valves and cylinders.
° Moisture will reduce tool performance and life if not
removed from compressed air.
° A filter-regulator-lubricator system is required and should be
located as close to tool as possible. A distance of less than
15 feet is recommended. Lubricator is not required for
oilless tools.
° Keep air filter clean. A dirty filter will reduce the air pressure
to the tool causing a reduction in power and efficiency.
° The air supply system must be able to provide air pressure
of 60 to 100 pounds per square inch at tool.
° All hoses and pipes in the air supply system must be clean
and free of moisture and foreign particles. Hoses must be
rated for a maximum working pressure of 150 PSI or 150%
of maximum system pressure, whichever is greater.
° Do not mount swivel connector in air supply line.
° The air pressure should be properly regulated.
° Different workpiece materials and different fastener lengths
will require different operating pressure.
° Be sure all connections in air supply system are sealed to
prevent air loss.
° Never connect a female quick-disconnect coupling to the
tool side of air line connection. A male, free-flow coupling
should be connected to the tool side of air line connection
(see Figure 1).
WARNING: The female coupling provides a seal preventing
loss of compressed air from compressor tank when discon-
nected from male coupling. If connected to tool side of air
supply, the female coupling could seal a compressed air
charge in the tool which could discharge if the tool trigger is
actuated.
Figure 1 - Air Supply Line
LOADING
Refer to Figures 2, 3 & 4 (page 4).
WARNING: Disconnect tool from air supply. Do not load tool
until you are ready to use it. Do not pull trigger or depress
contact trip while loading tool. Always load with nose of tool
pointing away from you and others. Always wear safety gog-
gles that comply with United States ANSI Z87.1.
NOTE: For best results, use Sears fasteners only.