Publicidad
Idiomas disponibles
Idiomas disponibles
Remote Control Features and Settings
• When turning the unit on, the remote control will
automatically return the louver to the previous set
position.
10. FAN Button
FAN mode circulates air only; there is not temperature
adjustment available. Use the fan speed button (7) to
adjust fan speed from low, medium, to high. Auto, Turbo,
and Quiet are not available.
11. EXTRA FUNCTION Button
Press the EXTRA FUNCTION button to view all other
operations. Press CONFIRM/CANCEL to select and save
the chosen operation. If no button is pressed for 10
seconds, the remote will exit EXTRA FUNCTION mode.
A) Refresh air
- Feature not available on this series.
B) A-B selection - This will allow you to control two
separate units with a single remote control. Note: This
feature would be setup at the time of installation by the
contractor.
C) Auto mode
- The heat pump will automatically
select Cool, Heat, or Fan operation according to set
temperature. When FAN is set to AUTO the heat pump
automatically adjusts the fan speed according to room
temperature.
D) Upper and Lower louver lock.
1. Upper louver lock
the top position. Commonly used during cooling.
2. Lower louver lock
the lower position. Commonly used during heating.
3. To unlock the louver press EXTRA FUNCTION button
until either a single louver icon
Note: When the louver is locked, the position cannot be
changed with the LOUVER UP/DOWN button.
E) Timer ON/OFF: Sets a countdown timer until the unit is
turned ON/OFF. TEMP+/TEMP- button is pressed with
the length of time increment/decrement in 0.5 hour
between 0-12 hours,and 1 hour increment/decrement
between 12-24 hours.
1. When the remote is set to ON, the system will turn off
until the countdown timer ends. Then the indoor unit will
turn on and operate in mode, temperature setting and
fan speed that was displayed when timer was set.
2. When the remote is set to OFF, the system will
remain ON until the countdown timer ends.
12. SLEEP Button
Sleep mode
Before going to bed, you can simply press the SLEEP
button and the unit will operate in SLEEP mode and bring
you a sound sleep.
Sleep operation Mode
1. Operation in COOL or DRY modes: One hour after
SLEEP mode starts, the temperature will rise 2°F above
set temperature. After another hour, the temperature
rises additional 2°F. The unit will run for additional six
hours before it turns off. The final temperature is 4°F
higher than initial set temperature. Using this feature
will lock the horizontal louver in
will lock the horizontal louver in
or oscillate icon
helps with achieving maximum efficiency and comfort
from your unit while you sleep.
2. Operation in Heat Mode: One hour after SLEEP
modestarts, the temperature will decrease 4°F below
set temperature. After another hour, the temperature
will decrease an additional 4°F. After an additional three
hours, the temperature will rise by 2°F. The unit will run
for an additional three hours before it turns off. The final
temperature is 6°F lower than the initial set
temperature. Using this feature will help with achieving
maximum efficiency and comfort from your unit while
you sleep.
3. In AUTO mode, the unit operates in corresponding
sleep mode adapted to the automatically selected
operation mode.
NOTE:
• When the unit is set to sleep mode, the fan speed will be
set to low speed and cannot be changed.
• When the TIMER function is set the sleeping function
.
cannot be set. If the sleeping function has been set and
the user sets the TIMER function, the sleeping function
will be canceled and the unit will be set to the timer
function.
13. Fahrenheit/Celsius Button
Press F/C to toggle remote and unit display temperature
between Fahrenheit and Celcius.
14. HEALTH Button
Feature is not Available.
15. Confirm/Cancel Button
Function: Setting and canceling timer and other
functions.
16. LOCK Button
Used to lock buttons and LCD Display
17. LIGHT Button
Turns indoor unit display on and off
18. RESET Button
If the remote control is not functioning properly, use a pen
point or similar object to depress this button to reset the
remote.
5
Publicidad
